Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
2009 Jeep Liberty 4WD V6-3.7L
Repair and Diagnosis: Technical Service Bulletins
2009 Jeep Liberty 4WD V6-3.7LSECTION Technical Service Bulletins
- How to Find Technical Service Bulletins by Category/Symptom
- Recalls
- Customer Interest
- Body - Water Leak At Rear Of Headliner
- Audio System - REW Or REX Radio Software Enhancements
- Antitheft System - Alarms Sounds Intermittently,No Start
- Body - Light To Moderate Paint Imperfections
- Engine Controls - MIL ON/DTC's P050D Or P2181 Set
- Engine Controls - MIL ON/DTC P0401 Set
- A/C - Water Leaks Onto Carpet Or Water In A/C Housing
- Fuel System/Body - Fuel Filler Neck To Body Grommet Play
- Audio System - Software Enhancements
- A/T - Converter Shudder On Vehicles With Less Than 4K Mi
- Engine Controls - MIL ON/DTC's P0123/P0222 Set
- Engine Controls - MIL ON/Multiple Ignition Coil DTC's
- Fuel System - Difficult Fuel Fill/Nozzle Shuts Off
- Keyless Entry - Intermittent No Start/Key Fobs Inop.
- Body - Sunroof Wind Noise/Auto Express Feature Inop.
- M/T - Pops Out Of 1st Gear On Acceleration
- Audio System - REN/REZ Radio Lock Up
- Body - Lower Door Hinge Popping Groaning Noises
- Instruments - Clock in Radio Loses Time
- Superceded Bulletins
- All Technical Service Bulletins
- Body - Water Leak At Rear Of Headliner
- Body/Frame - Welded Sheet Metal Repairs And Replacements
- Body - Don't Apply Corrosion Protection On Plastic Panels
- Body - Front Bumper Fascia Repair For License Bracket Holes
- Audio System - REW Or REX Radio Software Enhancements
- Wheels/Tires - Chrome Clad Wheel Balancing Info.
- Collision - Safety Cert./Tire Press. Label Replacement
- Antitheft System - Alarms Sounds Intermittently,No Start
- Steering/Suspension - Wheel Hub/Bearing Inspection COLL.
- Body - Light To Moderate Paint Imperfections
- Wheels - Reconditioned Wheel Usage
- Restraints - Replacement Seat Covers/Seat Cover Repairs
- Restraints - Use Of Salvaged Restraint System Components
- Body/Frame - Structural Repair Components
- Body/Frame - Usage Of Heat For Repair
- Engine Controls - MIL ON/DTC's P050D Or P2181 Set
- Engine Controls - MIL ON/DTC P0401 Set
- A/C - Water Leaks Onto Carpet Or Water In A/C Housing
- Fuel System/Body - Fuel Filler Neck To Body Grommet Play
- Audio System - Software Enhancements
- A/T - Converter Shudder On Vehicles With Less Than 4K Mi
- A/T - Repair/Replacement Guidelines
- Instruments - Vehicle Information Center Setup
- Engine Controls - MIL ON/DTC's P0123/P0222 Set
- Audio System - Radio Inop. After Battery Disconnect
- Maintenance - Fluid Flushing Information
- Wheels/Tires - Chrome Clad Wheel Balancing Information
- Engine Controls - MIL ON/Multiple Ignition Coil DTC's
- Fuel System - Difficult Fuel Fill/Nozzle Shuts Off
- Recall - Warranty Book Incorrect Emissions Information
- Keyless Entry - Intermittent No Start/Key Fobs Inop.
- Body - Sunroof Wind Noise/Auto Express Feature Inop.
- Entertainment System - Disabling Front Seat Video Source
- M/T - Pops Out Of 1st Gear On Acceleration
- Audio System - REN/REZ Radio Lock Up
- Body - Lower Door Hinge Popping Groaning Noises
- Body - Paint Overspray Removal Procedures
- Engine - Gasoline Engine Diagnostic Inspection Procedure
- Instruments - Clock in Radio Loses Time
- Paint - Clearcoat Blending During Refinish Process
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.