Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBā LIVE
HOMESERVICE MANUALSJEEP2008COMMANDER OVERLAND, RWDREPAIR AND DIAGNOSISACCESSORIES & EQUIPMENTCOMMUNICATION DEVICESELECTRONIC CONTROL MODULES (SERVICE INFORMATION)
2008 Jeep Commander Overland, RWD
Electronic Control Modules (Service Information)
2008 Jeep Commander Overland, RWDSECTION Electronic Control Modules (Service Information)
- Electronic Control Modules
- Standard Procedure
- Communication
- Data Link Connector
- Module-Adjustable Pedals
- Module-Antilock Brakes
- Module-Engine Control
- Description
- Operation
- Standard Procedure
- Pcm/ECM Programming - Diesel
- Pcm / TCM Flash Reprogramming
- Table Of Contents
- Section 1 - Pcm / TCM Flash Procedure
- REPAIR PROCEDURE - Using StarSCANĀ® or StarMOBILEĀ® Desktop Client
- REPAIR PROCEDURE - Using StarMOBILEĀ® Standalone Diagnostic Mode
- Section 2 - Additional Pcm / TCM Replacement Procedures
- Step-By-Step Instructions
- Section 3 - Authorized Modification Label
- Required Tools/Equipment:
- TECH TIPS and INFORMATION:
- Parts Required
- Pcm/ECM Programming - Diesel
- Removal
- Installation
- Module-Final Drive Control
- Module-Front Control
- Module-Memory Mirror
- Module-Memory Seat
- Module-Powertrain Control
- Description
- Operation
- Standard Procedure
- Pcm/ECM Programming - Gas
- Pcm / TCM Flash Reprogramming
- Table Of Contents
- Section 1 - Pcm / TCM Flash Procedure
- REPAIR PROCEDURE - Using StarSCANĀ® or StarMOBILEĀ® Desktop Client
- REPAIR PROCEDURE - Using StarMOBILEĀ® Standalone Diagnostic Mode
- Section 2 - Additional Pcm / TCM Replacement Procedures
- Step-By-Step Instructions
- Section 3 - Authorized Modification Label
- Required Tools/Equipment:
- TECH TIPS and INFORMATION:
- Parts Required
- Pcm/ECM Programming - Gas
- Removal
- Installation
- Module-Steering Control
- Module-Transmission Control
- Description
- Operation
- Transmission Control Module - 3.7L Gas/3.0L Diesel Vehicles
- Notes
- TCM Signals
- Selector Lever Position
- ATF Temperature Sensor
- Starter Interlock
- N2 and N3 Speed Sensors
- CAN C Bus Indirect Input Signals
- Shift Schedules
- Downshift Safety
- Adaptation
- Driving Style Adaptation
- Shift Time Adaptation (Shift Overlap Adaptation, Working Pressure)
- Fill Pressure Adaptation (Apply Pressure Adaptation, Modulating Pressure)
- Fill Time Adaptation (Engagement Time Adaptation)
- Controller Modes Of Operation
- Transmission Control Module - 4.7L/5.7L Vehicles
- Transmission Control Module - 3.7L Gas/3.0L Diesel Vehicles
- Standard Procedure
- Drive Learn - 4.7L/5.7L Vehicles
- Notes
- Learn A Smooth 1ST Neutral To Drive Shift
- Learn A Smooth Neutral To Drive Garage Shift
- Learn The 1ST 2-3 Shift After A Restart Or Shift To Reverse
- Learn A Smooth 2-3 And 3-4 Upshift
- Learn A Smooth 4-3 COASTDOWN And Part Throttle 4-3 KICKDOWN
- Learn A Smooth 1-2 Upshift And 3-2 KICKDOWN
- Learn A Smooth Manual 2-1 PULLDOWN Shift As Well As A Neutral To Reverse Shift
- Learn A Smooth Neutral To Reverse Shift
- Learn A Smooth 4-5 Upshift
- Transmission Control Module - Adaptation - 3.7L Gas/3.0L Diesel Vehicles
- Transmission Control Module - Quick Learn - 4.7L/5.7L Vehicles
- Drive Learn - 4.7L/5.7L Vehicles
- Removal
- Installation
- Node-Wireless Ignition
- Module-Glow Plug
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- ā¢ You smell fuel, burning insulation, or see smoke.
- ā¢ Brakes feel soft, pull hard to one side, or make grinding noises.
- ā¢ The engine overheats, stalls repeatedly, or misfires under load.
- ā¢ You are missing required tools, torque specs, or safe lifting equipment.
- ā¢ You are not confident in the next step or safety outcome.