SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2008COMMANDER LIMITED, 4.7 N, RWDREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTINFOTAINMENTNAVIGATION SYSTEM & TELECOMMUNICATION SYSTEM - ELECTRICAL DIAGNOSTICSNAVIGATION/TELECOMMUNICATION - ELECTRICAL DIAGNOSTICSDTC TROUBLESHOOTINGB143F-MICROPHONE 2 CIRCUIT HIGHDIAGNOSTIC TEST
2008 Jeep Commander Limited, 4.7 N, RWD

Diagnostic Test

2008 Jeep Commander Limited, 4.7 N, RWDSECTION Diagnostic Test
  1. CHECK FOR ACTIVE DTC 

    With the scan tool, read the active DTC's.

    Cycle the ignition switch from off to on at least 5 times, leaving the ignition on for a minimum of 90 seconds per cycle.

    Attempt to make a phone call with the system.

    With the scan tool, read the active DTC's.

    Does the scan tool display this DTC as active? 

    Yes 

    1. Go To  2.

    No 

    1. If the DTC is stored, check for an intermittent condition. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals.
  2. INSIDE REARVIEW MIRROR 
    Fig 1: Inside Rearview Mirror C2 Harness Connector
    GC0071882Courtesy of CHRYSLER LLC

    Turn the ignition off.

    Disconnect the Rearview Mirror C2 harness connector.

    Turn the ignition on.

    With the scan tool, read the active DTC's.

    Does the scan tool display this DTC as active? 

    Yes 

    1. Go To  3.

    No 

    1. Replace the Rearview Mirror in accordance with the service information.
    2. Perform BODY VERIFICATION TEST .
  3. (X722) MICROPHONE CIRCUITS SHORTED TO VOLTAGE 
    Fig 2: Measuring Voltage Of (X722) Microphone Circuit
    GC0071888Courtesy of CHRYSLER LLC

    Turn the ignition off.

    Disconnect the Hands Free Module harness connector.

    Turn the ignition on.

    Measure the voltage of the (X722) Microphone circuit.

    Is the voltage above 1.0 volt? 

    Yes 

    1. Repair the (X722) Microphone circuit for a short to voltage.
    2. Perform BODY VERIFICATION TEST .

    No 

    1. Go To  4.
  4. (X722) MICROPHONE 2 IN (+) CIRCUIT OPEN 
    Fig 3: Measuring Resistance Of (X722) Microphone 2 IN (+) Circuit Between HFM Connector And Inside Rearview Mirror Connector
    GC0071889Courtesy of CHRYSLER LLC

    Turn the ignition off.

    Measure the resistance of the (X722) Microphone 2 IN (+) circuit between the HFM connector and the inside rearview mirror connector.

    Is the resistance below 5.0 ohms? 

    Yes 

    1. Replace the Hands Free Module in accordance with the service information.
    2. Perform BODY VERIFICATION TEST .

    No 

    1. Repair the (X722) Microphone 2 IN (+) circuit for an open.
    2. Perform BODY VERIFICATION TEST .
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.