Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2002LIBERTY LIMITED EDITION 2WD V6-3.7L VIN KREPAIR AND DIAGNOSISSTARTING AND CHARGINGPOWER AND GROUND DISTRIBUTIONRELAYS AND MODULES - POWER AND GROUND DISTRIBUTIONPOWER DISTRIBUTION MODULESERVICE AND REPAIRPDC B+ TERMINAL MODULE
2002 Jeep Liberty Limited Edition 2WD V6-3.7L VIN K
PDC B+ Terminal Module
2002 Jeep Liberty Limited Edition 2WD V6-3.7L VIN KSECTION PDC B+ Terminal Module
Disassembly and Assembly
REMOVAL
The Power Distribution Center (PDC) cover, the PDC housing lower cover, the PDC relay wedges, the PDC mini fuse wedge, the PDC relay cassettes and the PDC B(+) terminal stud module (Fig. 4) are available for service replacement. The PDC cover can be simply unlatched and removed from the PDC housing without the PDC being removed or disassembled. Service of the remaining PDC components requires that the PDC be removed from its mounting and disassembled. Refer to Wiring Repair in Wiring Diagrams for the location of the wiring repair procedures.
1. Remove the PDC housing lower cover.
2. From the top of the PDC housing, use a small screwdriver or a terminal pick tool (Special Tool Kit 6680) to release the two latches that secure the B(+) terminal module in the PDC.
3. Gently and evenly press the two B(+) terminal studs down through the bus bar in the PDC.
4. From the bottom of the PDC housing, remove the B(+) terminal module from the PDC.
INSTALLATION
1. From the bottom of the PDC housing, align and insert the B(+) terminal module into the PDC.
2. From the bottom of the PDC housing, align and insert the two studs of the PDC B(+) terminal module through the bus bar in the PDC.
3. From the bottom of the PDC housing, press the B(+) terminal module gently and evenly into the PDC until both of the latches are fully engaged.
4. Install the PDC housing lower cover.
REMOVAL
Fig. 4 B+ Terminal Module:
The Power Distribution Center (PDC) cover, the PDC housing lower cover, the PDC relay wedges, the PDC mini fuse wedge, the PDC relay cassettes and the PDC B(+) terminal stud module (Fig. 4) are available for service replacement. The PDC cover can be simply unlatched and removed from the PDC housing without the PDC being removed or disassembled. Service of the remaining PDC components requires that the PDC be removed from its mounting and disassembled. Refer to Wiring Repair in Wiring Diagrams for the location of the wiring repair procedures.
1. Remove the PDC housing lower cover.
2. From the top of the PDC housing, use a small screwdriver or a terminal pick tool (Special Tool Kit 6680) to release the two latches that secure the B(+) terminal module in the PDC.
3. Gently and evenly press the two B(+) terminal studs down through the bus bar in the PDC.
4. From the bottom of the PDC housing, remove the B(+) terminal module from the PDC.
INSTALLATION
1. From the bottom of the PDC housing, align and insert the B(+) terminal module into the PDC.
2. From the bottom of the PDC housing, align and insert the two studs of the PDC B(+) terminal module through the bus bar in the PDC.
3. From the bottom of the PDC housing, press the B(+) terminal module gently and evenly into the PDC until both of the latches are fully engaged.
4. Install the PDC housing lower cover.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.