Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2002LIBERTY LIMITED EDITION 2WD V6-3.7L VIN KREPAIR AND DIAGNOSISSTARTING AND CHARGINGPOWER AND GROUND DISTRIBUTIONFUSE BLOCKSERVICE AND REPAIRRHD
2002 Jeep Liberty Limited Edition 2WD V6-3.7L VIN K
RHD
2002 Jeep Liberty Limited Edition 2WD V6-3.7L VIN KSECTION RHD
REMOVAL - RHD
The following junction block removal procedure applies to Right Hand Drive (RHD) vehicles only
1. Disconnect and isolate the negative battery cable.
2. Remove the right end cap from the instrument panel.
3. Unsnap and remove the right outboard trim bezel from the instrument panel Located just to the right of the steering column.
4. Remove the steering column opening cover.
5. Remove the right cowl trim panel from the vehicle.
6. Remove the courtesy lamp from under the right side of the instrument panel. This will allow sufficient room to remove the junction block from under the instrument panel.
7. Working through the steering column opening cover, remove the three bulkhead and two body controller electrical connectors from the junction block assembly
8. Remove the two ground wires from the right lower kick panel area. Located directly behind the kick trim panel. This will allow sufficient room to remove the junction block from under the instrument panel.
9. Remove the upper and forward most (in relation to the vehicle) group of relays from the junction block. This will allow sufficient room to remove the junction block from under the instrument panel.
10. Remove the four junction block retaining screws and remove the junction block from under the instrument panel. It will be necessary to position the under instrument panel wire harness out of the way to remove the junction block.
INSTALLATION - RHD
1. Position the junction block and install the four junction block retaining screws.
2. Install the upper and forward most group of relays in the junction block.
3. Install the two ground wires on the right lower kick panel area.
4. Working through the steering column opening cover, install the three bulkhead and two body controller electrical connectors on the junction block assembly.
5. Install the courtesy lamp under the right side of the instrument panel.
6. Install the right cowl trim panel on the vehicle.
7. Install the steering column opening cover
8. Install the right outboard trim bezel on the instrument panel.
9. Install the right end cap on the instrument panel.
10. Connect the negative battery cable.
The following junction block removal procedure applies to Right Hand Drive (RHD) vehicles only
1. Disconnect and isolate the negative battery cable.
2. Remove the right end cap from the instrument panel.
3. Unsnap and remove the right outboard trim bezel from the instrument panel Located just to the right of the steering column.
4. Remove the steering column opening cover.
5. Remove the right cowl trim panel from the vehicle.
6. Remove the courtesy lamp from under the right side of the instrument panel. This will allow sufficient room to remove the junction block from under the instrument panel.
7. Working through the steering column opening cover, remove the three bulkhead and two body controller electrical connectors from the junction block assembly
8. Remove the two ground wires from the right lower kick panel area. Located directly behind the kick trim panel. This will allow sufficient room to remove the junction block from under the instrument panel.
9. Remove the upper and forward most (in relation to the vehicle) group of relays from the junction block. This will allow sufficient room to remove the junction block from under the instrument panel.
10. Remove the four junction block retaining screws and remove the junction block from under the instrument panel. It will be necessary to position the under instrument panel wire harness out of the way to remove the junction block.
INSTALLATION - RHD
1. Position the junction block and install the four junction block retaining screws.
2. Install the upper and forward most group of relays in the junction block.
3. Install the two ground wires on the right lower kick panel area.
4. Working through the steering column opening cover, install the three bulkhead and two body controller electrical connectors on the junction block assembly.
5. Install the courtesy lamp under the right side of the instrument panel.
6. Install the right cowl trim panel on the vehicle.
7. Install the steering column opening cover
8. Install the right outboard trim bezel on the instrument panel.
9. Install the right end cap on the instrument panel.
10. Connect the negative battery cable.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.