Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1990 Jeep WagoneerFACTORY OEM SERVICE PROCEDURE
Diagnostic Trouble Code (DTC) Menu
DTC IDENTIFICATION
| DTC | Fault Condition |
|---|---|
| 1000 | Ignition Line Low. |
| 1001 | Ignition Line High. |
| 1002 | O2 Heater Low Line. |
| 1004 | Battery Voltage Low. |
| 1005 | Sensor Ground Line Out Of Limits. |
| 1013 | MPA Line High. |
| 1014 | Fuel Pump Line Low. |
| 1015 | Fuel Pump Line High. |
| 1016 | MAT Sensor Line Low. |
| 1017 | MAT Sensor Line High. |
| 1018 | No Serial Data. |
| 1020 | No Sync Pulse Seen. |
| 1021 | Engine Failed To Start Due To Mechanical, Fuel Or Ignition Problem. |
| 1022 | Start Line Low. |
| 1027 | ECU Sees Wide Open Throttle. |
| 1028 | ECU Does Not See Wide Open Throttle. |
| 1031 | ECU Sees Closed Throttle. |
| 1032 | ECU Does Not See Closed Throttle. |
| 1037 | TPS Circuit Reads Low. |
| 1038 | Park/Neutral Line High (A/T). |
| 1039 | Park/Neutral Line Low (A/T). |
| 1040 | Latched B+ Line Low. |
| 1041 | Latched B+ Line High. |
| 1042 | No Latched B+ 1/2 Volt Drop. |
| 1044 | Fault In Shift Light Circuit (M/T). |
| 1047 | Wrong ECU. |
| 1048 | Manual Vehicle Equipped With Automatic ECU. |
| 1049 | Automatic Transmission Vehicle Configuration. |
| 1050 | Idle RPM Less Than 500. |
| 1051 | Idle RPM Greater Than 2000. |
| 1052 | MAP Sensor Out Of Limits. |
| 1053 | Change In Map Reading Out Of Limits. |
| 1054 | Coolant Temperature Sensor Line Low. |
| 1055 | Coolant Temperature Sensor Line High. |
| 1056 | Inactive Coolant Temperature Sensor. |
| 1057 | Knock Circuit Shorted. |
| 1058 | Knock Value Out Of Limits. |
| 1059 | A/C Request Circuit Low. |
| 1060 | A/C Request Circuit High. |
| 1061 | A/C Select Circuit Low. |
| 1062 | A/C Select Circuit High. |
| 1063 | A/C Clutch Circuit Low. |
| 1064 | A/C Clutch Circuit High. |
| 1065 | O2 Sensor Reads Rich. |
| 1066 | O2 Sensor Reads Lean. |
| 1067 | Latch Relay Circuit Low. |
| 1068 | Latch Relay Circuit High. |
| 1069 | No tach. |
| 1073 | ECU Does Not See Speed Sensor. |
| 1200 | Defective ECU Or Short To Voltage. |
| 1201 | Injector Short To B+. |
| 1202 | All Injectors Shorted To Ground. |
| 1203 | Injector #1 Shorted To Ground. |
| 1204 | Injector #2 Shorted To Ground. |
| 1205 | Injector #3 Shorted To Ground. |
| 1206 | Injector #4 Shorted To Ground. |
| 1207 | Injector #5 Shorted To Ground. |
| 1208 | Injector #6 Shorted To Ground. |
| 1209 | All Injectors Open. |
| 1210 | Injector #1 Circuit Open. |
| 1211 | Injector #2 Circuit Open. |
| 1212 | Injector #3 Circuit Open. |
| 1213 | Injector #4 Circuit Open. |
| 1214 | Injector #5 Circuit Open. |
| 1215 | Injector #6 Circuit Open. |
| 1216 | No Voltage At ECU From A/C Relay. |
| 1217 | No Voltage At ECU From O2 Heater Relay. |
| 1218 | No Voltage At ECU From Power Latch Relay. |
| 1219 | No Voltage At ECU From Shift Light. |
| 1220 | No Voltage At ECU From EGR Solenoid. |
| 1222 | MPA Not Grounded. |
| 1223 | Checking For Open Injector Feed Circuits |
NOTE:
Compare fault code to appropriate diagnostic chart.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
