Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1990 Jeep WagoneerFACTORY OEM SERVICE PROCEDURE
Engine Controls - Tests W/Codes - 4.0L
- Introduction
- Self-Diagnostic System
- Testing
- Diagnosis With DRB-II & Jeep Adapter
- Diagnostic Trouble Code (DTC) Menu
- Ecu Location
- Code Charts
- Fault 1000: Ignition Circuit Low
- Fault 1001: Ignition Circuit High
- Fault 1002: O2 Heater Circuit Low
- Fault 1004: Battery Voltage Low
- Fault 1005: Sensor Ground Circuit Out Of Limits
- Fault 1013: Ignition Circuit High
- Fault 1014: Fuel Pump Circuit Low
- Fault 1015: Fuel Pump Circuit High
- Fault 1016: Manifold Air Temperature (Mat) Circuit Low
- Fault 1017: Manifold Air Temperature (Mat) Circuit High
- Fault 1018: No Serial Data
- Fault 1020: No Sync Pulse Seen
- Fault 1021: Engine Failed To Start Due To Mechanical, Fuel Or Ignition
- Fault 1022: Start Circuit Low
- Fault 1027: Ecu Sees Wide Open Throttle
- Fault 1028: Ecu Doesn't See Wide Open Throttle
- Fault 1031: Ecu Sees Closed Throttle
- Fault 1032: Ecu Doesn't See Closed Throttle
- Fault 1037: Throttle Position Sensor (TPS) Circuit Low
- Fault 1038: Park/Neutral Circuit High (A/T)
- Fault 1039: Park/Neutral Circuit Low (A/T)
- Fault 1040: Latched B+ Circuit Low
- Fault 1041: Latched B+ Circuit High
- Fault 1042: No Latched B+ 1/2 Volt Drop
- Fault 1044: Fault In Shift Light Circuit (M/T)
- Fault 1047: Wrong Ecu
- Fault 1048: M/T Vehicle With A/T Ecu
- Fault 1049: A/T Vehicle With M/T Ecu
- Fault 1050: Idle Rpm Less Than 500
- Fault 1051: Idle Rpm Greater Than 2000
- Fault 1052: Map Sensor Out Of Limits
- Fault 1053: Change In Map Reading Out Of Limits
- Fault 1054: Coolant Temp Sensor Circuit Low
- Fault 1055: Coolant Temp Sensor Circuit High
- Fault 1056: Inactive Coolant Temp Sensor
- Fault 1057: Knock Circuit Shorted
- Fault 1058: Knock Value Out Of Limits
- Fault 1059: A/C Request Circuit Low
- Fault 1060: A/C Request Circuit High
- Fault 1061: A/C Select Circuit Low
- Fault 1062: A/C Select Circuit High
- Fault 1063: A/C Clutch Circuit Low
- Fault 1064: A/C Clutch Circuit High
- Fault 1065: O2 Sensor Reads Rich
- Fault 1066: O2 Sensor Reads Lean
- Fault 1067: Latch Relay Circuit Low
- Fault 1068: Latch Relay Circuit High
- Fault 1069: No Tach
- Fault 1073: Ecu Doesn't See Speed Sensor
- Fault 1200: Defective Ecu Or Short To Voltage
- Fault 1201: Injector Short To B+
- Fault 1202: All Injectors Shorted To Ground
- Fault 1203: Injector No. 1 Shorted To Ground
- Fault 1204: Injector No. 2 Shorted To Ground
- Fault 1205: Injector No. 3 Shorted To Ground
- Fault 1206: Injector No. 4 Shorted To Ground
- Fault 1207: Injector No. 5 Shorted To Ground
- Fault 1208: Injector No. 6 Shorted To Ground
- Fault 1209: All Injectors Open
- Fault 1210: Injector No. 1 Circuit Open
- Fault 1211: Injector No. 2 Circuit Open
- Fault 1212: Injector No. 3 Circuit Open
- Fault 1213: Injector No. 4 Circuit Open
- Fault 1214: Injector No. 5 Circuit Open
- Fault 1215: Injector No. 6 Circuit Open
- Fault 1216: No Voltage At Ecu From A/C Relay
- Fault 1217: No Voltage At Ecu From O2 Heater Relay
- Fault 1218: No Voltage At Ecu From Power Latch Relay
- Fault 1219: No Voltage At Ecu From Shift Light
- Fault 1220: No Voltage At Ecu From EGR Solenoid
- Fault 1222: Ignition Module (MPA) Not Grounded
- Fault 1223: Checking For Open Injector Feed Circuit
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
