Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJAGUAR2018XE BASE, 2.0L ENG VIN N, AWDREPAIR AND DIAGNOSISQUICK LOOKUPSDTC INDEXDIAGNOSTIC TROUBLE CODE INDEX DTC: IMAGE PROCESSING MODULE (IPMA) -- XE (X760)
2018 Jaguar XE Base, 2.0L Eng VIN N, AWD
Diagnostic Trouble Code Index DTC: Image Processing Module (IPMA) -- XE (X760)
2018 Jaguar XE Base, 2.0L Eng VIN N, AWDSECTION Diagnostic Trouble Code Index DTC: Image Processing Module (IPMA) -- XE (X760)
- Diagnostic Trouble Code Index DTC: Image Processing Module (IPMA)
- Description And Operation
- Image Processing Module (IPMA)
- Notes
- DTC B1206-53: Crash Occurred - Deactivated
- DTC B151F-18: Auxiliary Cooling Fan - Circuit current below threshold
- DTC B151F-19: Auxiliary Cooling Fan - Circuit current above threshold
- DTC B151F-31: Auxiliary Cooling Fan - No signal
- DTC B151F-91: Auxiliary Cooling Fan - Parametric
- DTC B1DA9-92: Autonomous Emergency Braking Function - Performance or incorrect operation
- DTC C1001-49: Vision System Camera - Internal electronic failure
- DTC C1001-57: Vision System Camera - Invalid/incomplete software component
- DTC C1001-78: Vision System Camera - Alignment or adjustment incorrect
- DTC C1001-98: Vision System Camera - Component or system over temperature
- DTC U0001-81: High Speed CAN Communication Bus - Invalid serial data received
- DTC U0001-82: High Speed CAN Communication Bus - Alive/sequence counter incorrect/not updated
- DTC U0001-83: High Speed CAN Communication Bus - Value of signal protection calculation Incorrect
- DTC U0001-87: High Speed CAN Communication Bus - Missing message
- DTC U0001-88: High Speed CAN Communication Bus - Bus off
- DTC U0002-82: High Speed CAN Communication Bus Performance - Alive/sequence counter incorrect/not updated
- DTC U0300-00: Internal Control Module Software Incompatibility - No sub type information
- DTC U2300-51: Central Configuration - Not programmed
- DTC U2300-54: Central Configuration - Missing calibration
- DTC U2300-55: Central Configuration - Not configured
- DTC U2300-56: Central Configuration - Invalid/incomplete configuration
- DTC U2300-64: Central Configuration - Signal plausibility failure
- DTC U3000-44: Control Module - Data memory failure
- DTC U3000-68: Control Module - Event information
- DTC U3000-96: Control Module - Component internal failure
- DTC U3000-97: Control Module - Component or system operation obstructed or blocked
- DTC U3003-16: Battery Voltage - Circuit voltage below threshold
- DTC U3003-17: Battery Voltage - Circuit voltage above threshold
- Image Processing Module (IPMA)
- Description And Operation
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.