Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJAGUAR2011XJ SUPERCHARGEDREPAIR AND DIAGNOSISGENERAL INFORMATIONDTC INDEXDIAGNOSTIC TROUBLE CODE (DTC) INDEX DTC: TRANSFER CASE CONTROL MODULE (TCCM) -- XJ/X351
2011 Jaguar XJ Supercharged
Diagnostic Trouble Code (DTC) Index DTC: Transfer Case Control Module (TCCM) -- XJ/X351
2011 Jaguar XJ SuperchargedSECTION Diagnostic Trouble Code (DTC) Index DTC: Transfer Case Control Module (TCCM) -- XJ/X351
- Diagnostic Trouble Code (DTC) Index DTC: Transfer Case Control Module (TCCM)
- Description And Operation
- Transfer Case Control Module (TCCM)
- Notes
- B1142-62 Ignition Status 1 - Signal compare failure
- P080A-56 Clutch Position Not Learned - Invalid/incomplete configuration
- P0810-04 Clutch Position Control Error - System internal failures
- P0810-07 Clutch Position Control Error - Mechanical failures
- P0810-56 Clutch Position Control Error - Invalid/incomplete configuration
- P0810-78 Clutch Position Control Error - Alignment or adjustment incorrect
- P170E-92 Clutch Delivered Torque Performance - Performance or incorrect operation
- P173A-64 Clutch Actuator Position Sensor Circuit Range/Performance - Signal plausibility failure
- P175B-00 Transfer Case Clutch Deteriorated - No sub type information
- P175C-00 Transfer Case Fluid Deteriorated - No sub type information
- P215A-62 Vehicle Speed/Wheel Speed Correlation - Signal compare failure
- P2787-98 Clutch Temperature Too High - Component or system over temperature
- U0001-81 High Speed CAN Communication Bus - Invalid serial data received
- U0001-87 High Speed CAN Communication Bus - Missing message
- U0001-88 High Speed CAN Communication Bus - Bus off
- U0300-00 Internal Control Module Software Incompatibility - No sub type information
- U2012-4A Car Configuration Parameter(s) - Incorrect component installed
- U2100-54 Initial Configuration Not Complete - Missing calibration
- U3000-47 Control Module - Watchdog/safety microcontroller failure
- U3000-49 Control Module - Internal electronic failure
- U3000-4B Control Module - Over temperature
- U3006-13 Control Module Input Power "A" - Circuit open
- U3006-16 Control Module Input Power "A" - Circuit voltage below threshold
- U3006-17 Control Module Input Power "A" - Circuit voltage above threshold
- U3006-62 Control Module Input Power "A" - Signal compare failure
- U3007-13 Control Module Input Power "B" - Circuit open
- U3007-16 Control Module Input Power "B" - Circuit voltage below threshold
- U3007-17 Control Module Input Power "B" - Circuit voltage above threshold
- U3007-62 Control Module Input Power "B" - Signal compare failure
- Transfer Case Control Module (TCCM)
- Description And Operation
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.