SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSISUZU2006ASCENDER S, 5.3 M, 4WDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 66 (DISC BRAKE SYSTEM)REPAIR INSTRUCTIONSDISC BRAKE HARDWARE REPLACEMENT - REARINSTALLATION PROCEDURE
2006 Isuzu Ascender S, 5.3 M, 4WD

Installation Procedure

2006 Isuzu Ascender S, 5.3 M, 4WDSECTION Installation Procedure
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2004 Oldsmobile Bravada, 2004 GMC Envoy XUV, 2004 GMC Envoy XL, 2004 GMC Envoy, and 2004 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Removing/Installing Caliper Bracket Bushings
    GM788344Courtesy of GENERAL MOTORS CORP.
  1. Install the guide pin bushing in the brake caliper mounting bracket.
    2. Fig 2: Identifying Brake Caliper Guide Pins
    GM788831Courtesy of GENERAL MOTORS CORP.
  2. Install the brake caliper guide pins.
    3. Fig 3: View Of Brake Caliper Guide Pin
    GM156329Courtesy of GENERAL MOTORS CORP.
  3. Apply high temperature silicone brake lubricant to the brake caliper guide pins. DO NOT apply to the brake caliper hardware or the retaining clips.
    4. Fig 4: View Of Caliper Mounting Bracket & Rotor
    GM748570Courtesy of GENERAL MOTORS CORP.
  4. Install the brake caliper mounting bracket.
    5. NOTE: Refer to Fastener Notice .
  5. Install the brake caliper mounting bolts.

    Tighten:  Tighten the disc brake caliper mounting bracket bolts to 200 N.m (148 lb ft).

    6. Fig 5: View Of Caliper Bracket
    GM748563Courtesy of GENERAL MOTORS CORP.
  6. Install the brake pad retaining clips on the brake caliper mounting bracket.
    7. Fig 6: Caliper Mounting View
    GM748557Courtesy of GENERAL MOTORS CORP.
  7. Install the brake pads to the brake caliper mounting bracket.
    8. Fig 7: View Of Caliper
    GM787920Courtesy of GENERAL MOTORS CORP.
  8. Install the brake pad retaining clip to the brake caliper.
    9. Fig 8: View Of Caliper To Caliper Mounting Bracket
    GM748566Courtesy of GENERAL MOTORS CORP.
  9. Install the brake caliper assembly. Refer to Brake Caliper Replacement - Rear .
  10. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  11. Lower the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
    12. CAUTION: Do not move the vehicle until a firm brake pedal is obtained. Failure to obtain a firm pedal before moving vehicle may result in personal injury.
  12. Pump the brake pedal slowly and firmly in order to seat the brake pads.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.