SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSISUZU2006ASCENDER S, 5.3 M, 4WDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 537 (SUPPLEMENTAL INFLATABLE RESTRAINT SYSTEM)REPAIR INSTRUCTIONSINFLATABLE RESTRAINT SEAT POSITION SENSOR REPLACEMENTREMOVAL PROCEDURE
2006 Isuzu Ascender S, 5.3 M, 4WD

Removal Procedure

2006 Isuzu Ascender S, 5.3 M, 4WDSECTION Removal Procedure
WARNING: This page is about a different car, the 2009 GMC Envoy and 2009 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.
  1. Remove the seat from the vehicle. Refer to Front Seat Replacement - Bucket .
    2. Fig 1: View Of J-Strips
    GM1333089Courtesy of GENERAL MOTORS CORP.
  2. Unclip the front, rear, and side J-strips (1, 2) on the underside of the seat.
  3. Remove the lumbar knob by pulling the knob straight away from the seat, if equipped.
  4. Remove the recliner handle. Refer to Driver or Passenger Seat Recliner Handle Replacement .
    5. Fig 2: View Of Lumbar Adjustment Mechanism & Retaining Screws
    GM1333092Courtesy of GENERAL MOTORS CORP.
  5. Remove the screws (2) that retain the lumbar adjustment mechanism (1) to the seat adjuster.
  6. Remove the lumbar cable from the lumbar adjustment mechanism.
    7. Fig 3: View Of Seat Recliner Bolts
    GM1333093Courtesy of GENERAL MOTORS CORP.
  7. Remove the 2 bolts (1) securing the seat recliner to the seat adjuster.
  8. Remove the seat back assembly from the seat cushion assembly.
    9. Fig 4: View Of Seat Buckle Electrical Connector & Wiring Harness
    GM1333091Courtesy of GENERAL MOTORS CORP.
  9. Disconnect the seat belt buckle electrical connector (1).
  10. Disconnect the wiring harness (2) from the seat position switch.
    11. Fig 5: View Of Seat Belt Buckle Assembly
    GM1333095Courtesy of GENERAL MOTORS CORP.
  11. Remove the bolt (2) securing the seat belt buckle assembly (1) to the seat adjuster.
  12. Remove the seat cushion cover and foam.
  13. Remove the assist spring.
    14. Fig 6: View Of Wire Harness & Seat Cushion Frame Nuts
    GM1333096Courtesy of GENERAL MOTORS CORP.
  14. Remove the 4 nuts (1) securing the seat cushion frame to the seat adjusters.
  15. Remove the seat adjusters.
    16. Fig 7: View Of Seat Position Switch
    GM1333097Courtesy of GENERAL MOTORS CORP.
  16. Remove the 2 nuts (1) securing the seat position switch (3) to the seat adjuster (2).
  17. Drill out the rivets securing the sensor to the bracket.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.