Memory Seat Module - Driver X3 (w/Memory)

2006 Isuzu Ascender S, 5.3 M, 4WDSECTION Memory Seat Module - Driver X3 (w/Memory)
WARNING: This page is about a different car, the 2008 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Memory Seat Module Connector End View - Driver X3 (w/Memory)
GM130690Courtesy of GENERAL MOTORS CORP.
Memory Seat Module - Driver X3 (w/Memory)

Pin Wire Circuit Function
A1 0.35 BK 5289 Low Reference (JF4)
A2 - - Not Used
A3 0.35 YE 1063 Driver Seat Lumbar Horizontal Position Sensor Signal
A4 0.35 WH/BK 570 Driver Seat Recline Motor Position Sensor Signal
A5 0.35 D-GN 569 Horizontal Seat Motor Position Sensor Signal
A6 0.35 TN 568 Rear Vertical Seat Motor Position Sensor Signal
A7 0.35 BN/WH 557 Front Vertical Seat Motor Position Sensor Signal
A8-A9 - - Not Used
A10 0.8 D-BU 5475 Passenger Heated Seat Back Temperature Sensor Signal (w/Heat)
A11 0.35 YE/BK 2079 Heated Seat Cushion Temperature Sensor Signal (w/Heat)
A12 - - Not Used
B1 0.35 TN 5604 Adjustable Pedal Relay Rearward Control (JF4)
B2 0.35 YE 5603 Adjustable Pedal Relay Forward Control (JF4)
B3-B4 - - Not Used
B5 0.8 PK 610 Driver Seat Lumbar Motor Rearward Control
B6 0.8 D-BU 611 Driver Seat Lumbar Motor Forward Control
B7 0.8 TN 2481 Passenger Heated Seat Back Element Supply Voltage (w/Heat)
B8 0.8 BK 2479 Passenger Heated Seat Cushion Element Supply Voltage (w/Heat)
B9 0.8 PK 2480 Passenger Heated Seat Element Control (w/Heat)
B10 0.8 BN 2432 Heated Seat Back Element Supply Voltage (w/Heat)
B11 0.8 L-GN 2077 Heated Seat Cushion Element Supply Voltage (w/Heat)
B12 0.8 L-GN 2078 Heated Seat Cushion Element Control (w/Heat)
Connector Part Information 
  • OEM: 12110206
  • Service: 12110206
  • Description: 24-Way F Metri-Pack 100 Series (L-BU)
Terminal Part Information 
  • Pins: A1, A3-A7, A11, B1-B2
  • Terminal/Tray: 12146447/3
  • Core/Insulation Crimp: E/C
  • Release Tool/Test Probe: 12031876-1/J-35616-6 (BN)
  • Pins: A10, B5-B12
  • Terminal/Tray: 12146448/19
  • Core/Insulation Crimp: E/C
  • Release Tool/Test Probe: 12031876-1/J-35616-6 (BN)
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • You smell fuel, burning insulation, or see smoke.
  • Brakes feel soft, pull hard to one side, or make grinding noises.
  • The engine overheats, stalls repeatedly, or misfires under load.
  • You are missing required tools, torque specs, or safe lifting equipment.
  • You are not confident in the next step or safety outcome.