Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSISUZU2006ASCENDER S, 5.3 M, 4WDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 209 (POWER SEAT SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESSCAN TOOL DATA LIST
2006 Isuzu Ascender S, 5.3 M, 4WD
Scan Tool Data List
2006 Isuzu Ascender S, 5.3 M, 4WDSECTION Scan Tool Data List
WARNING: This page is about a different car, the 2007 Isuzu Ascender, 2007 GMC Envoy, 2007 Chevrolet TrailBlazer, and 2007 Buick Rainier. However, it is still accessible from the selected car via links, so may be relevant.
Driver Seat Module (DSM)
| Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
|---|---|---|---|
| Operating Conditions: Ignition OFF | |||
| 8-Digit GM Part Number | Module Information 1 | Numeric | Varies |
| Battery Voltage | Inputs/Outputs | Volts | Varies |
| Exit Front Vertical Value | Memory Data | 0-5 Volts | Varies |
| Exit Horizontal Lumbar Value | Memory Data | 0-5 Volts | Varies |
| Exit Horizontal Value | Memory Data | 0-5 Volts | Varies |
| Exit Rear Vertical Value | Memory Data | 0-5 Volts | Varies |
| Exit Recline Value | Memory Data | 0-5 Volts | Varies |
| Exit Vertical Lumbar Value | Memory Data | 0-5 Volts | Varies |
| Front Vertical Motor | Inputs/Outputs | Up/Down/Inactive | Inactive |
| Front Vertical Position | Sensor Data | 0-5 Volts | Varies |
| Front Vertical Position Switch | Inputs/Outputs | Up/Down/Inactive | Inactive |
| Horizontal Lumbar Motor | Inputs/Outputs | Forward/Back/Inactive | Inactive |
| Horizontal Lumbar Position | Sensor Data | 0-5 Volts | Varies |
| Horizontal Motor | Inputs/Outputs | Forward/Back/Inactive | Inactive |
| Horizontal Position Switch | Inputs/Outputs | Forward/Back/Inactive | Inactive |
| Ign. Since Current DTC | Inputs/Outputs | Cycles | Varies |
| Julian Date of Build | Module Information 1 | Numeric | Varies |
| Last Memory Recall | Memory Data | Memory 1 or 2 | Last memory pressed |
| Last Memory Set | Memory Data | Invalid/Memory 1 or 2 | Memory 1 or 2 |
| Lumbar/Bolster Switch | Inputs/Outputs | Forward/Rearward/Downward/Upward/Idle | Idle |
| Manufacture Enable Counter | Module Information 2 | 0-255 | 0 |
| Memory 1 Front Vertical Value | Memory Data | 0-5 Volts | Varies |
| Memory 2 Front Vertical Value | Memory Data | 0-5 Volts | Varies |
| Memory 1 Horizontal Lumbar Value | Memory Data | 0-5 Volts | Varies |
| Memory 2 Horizontal Lumbar Value | Memory Data | 0-5 Volts | Varies |
| Memory 1 Horizontal Value | Memory Data | 0-5 Volts | Varies |
| Memory 2 Horizontal Value | Memory Data | 0-5 Volts | Varies |
| Memory 1 Rear Vertical Value | Memory Data | 0-5 Volts | Varies |
| Memory 2 Rear Vertical Value | Memory Data | 0-5 Volts | Varies |
| Memory 1 Recline Value | Memory Data | 0-5 Volts | Varies |
| Memory 2 Recline Value | Memory Data | 0-5 Volts | Varies |
| Memory 1 Vertical Lumbar Value | Memory Data | 0-5 Volts | Varies |
| Memory 2 Vertical Lumbar Value | Memory Data | 0-5 Volts | Varies |
| Recline Position | Sensor Data | 0-5 Volts | Varies |
| Recline Switch | Inputs/Outputs | Forward/Back/Inactive | Inactive |
| Recliner Motor | Inputs/Outputs | Forward/Back/Inactive | Inactive |
| Rear Vertical Motor | Inputs/Outputs | Up/Down/Inactive | Inactive |
| Rear Vertical Position | Sensor Data | 0-5 Volts | Varies |
| Rear Vertical Position Switch | Inputs/Outputs | Up/Down/Inactive | Inactive |
| Seat Horizontal Position | Sensor Data | 0-5 Volts | Varies |
| Software Part Number | Module Information 2 | Numeric | Varies |
| Software Revision Number | Module Information 2 | Two Letters | Varies |
| Vertical Lumbar Motor | Inputs/Outputs | Up/Down/Inactive | Inactive |
| Vertical Lumbar Position | Sensor Data | 0-5 Volts | Varies |
| Year Module Built | Module Information 1 | Numeric | Varies |
Driver Door Module (DDM)
| Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
|---|---|---|---|
| Operating Conditions: Ignition OFF | |||
| Memory Switch | Inputs | Memory 1/Memory 2/Idle | Idle |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.