SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSISUZU2006ASCENDER S, 5.3 M, 4WDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 173 (CELLULAR SYSTEM, ENTERTAINMENT SYSTEM, AND NAVIGATION SYSTEM)REPAIR INSTRUCTIONSCOAXIAL CABLE REPLACEMENT - CELLULAR TELEPHONEINSTALLATION PROCEDURE
2006 Isuzu Ascender S, 5.3 M, 4WD

Installation Procedure

2006 Isuzu Ascender S, 5.3 M, 4WDSECTION Installation Procedure
WARNING: This page is about a different car, the 2007 Isuzu Ascender, 2007 GMC Envoy, 2007 Chevrolet TrailBlazer, and 2007 Buick Rainier. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Identifying Coax Cable & Window Mounted Coupling
    GM826144Courtesy of GENERAL MOTORS CORP.
  1. Connect the coax cable (1) to the window mounted coupling.
    2. Fig 2: View Of Coax Cable Fasteners In Third Left Pillar
    GM826148Courtesy of GENERAL MOTORS CORP.
  2. Attach the coax cable fasteners to the left third pillar.
    3. Fig 3: View Of Coax Cable Fasteners In Floor Panel
    GM826146Courtesy of GENERAL MOTORS CORP.
  3. Attach the coax cable fasteners to the floor panel.
  4. Position the carpet to the floor panel, aligning the holes in the carpet to the seat studs on the floor panel.
  5. Pass the cellular telephone coax cable through the carpet opening
  6. Install the child restraint tether anchors. Refer to Child Restraint Tether Anchor Replacement - Rear No. 1 .
  7. Install the tool kit carrier.
    8. NOTE: Refer to Fastener Notice .
  8. Install the 3 tool carrier nuts to the floor studs.

    Tighten:  Tighten the nuts to 7 N.m (62 lb in).

  9. Install the lower rear quarter trim panels. Refer to Trim Panel Replacement - Rear Quarter - Left or to Trim Panel Replacement - Rear Quarter - Right .
  10. Install the rear quarter upper trim panels. Refer to Rear Quarter Upper Trim Panel Replacement (TrailBlazer, Envoy) .
  11. Install the center pillar trim panels. Refer to Center Pillar Garnish Molding Replacement .
  12. Install the left coat hook. Refer to Coat Hook Replacement .
  13. Install the rear door sill plates. Refer to Rear Side Door Sill Plate Replacement .
  14. Install the front door sill plates. Refer to Front Side Door Sill Plate Replacement .
  15. Instal the seat back, right and left side. Refer to Seat Back Replacement - Rear No. 1 .
  16. Install the navigation control processor bracket to the floor panel. Refer to Navigation Control Processor Bracket Replacement (TrailBlazer EXT/Envoy XL)  or Navigation Control Processor Bracket Replacement (TrailBlazer/Envoy/Rainier) .
  17. Install the communication interface module. Refer to Communication Interface Module Replacement (TrailBlazer EXT, Envoy XL)  or Communication Interface Module Replacement (TrailBlazer, Envoy, Rainier) .
  18. Install the right rear seat cushion. Refer to Seat Cushion Replacement - Rear No. 1 (TrailBlazer, Envoy, Rainier) .
  19. Adjust the right seat cushion to a passenger position.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.