SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSISUZU2006ASCENDER S, 5.3 M, 4WDREPAIR AND DIAGNOSISENGINE PERFORMANCETESTING & DIAGNOSISENGINE CONTROL SYSTEM - 5.3L - INTRODUCTION (2 OF 2)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2006 Isuzu Ascender S, 5.3 M, 4WD

Fastener Tightening Specifications

2006 Isuzu Ascender S, 5.3 M, 4WDSECTION Fastener Tightening Specifications
Fastener Tightening Specifications

Application Specifications
Metric English
Accelerator Pedal Position (APP) Sensor Bolt 20 N.m 15 lb ft
Air Cleaner Housing Nut 12 N.m 106 lb in
Air Cleaner Outlet Duct Bolt 10 N.m 89 lb in
Air Cleaner Outlet Duct Clamp 7 N.m 62 lb in
Camshaft Position (CMP) Sensor Bolt 29 N.m 21 lb ft
Crankshaft Position (CKP) Sensor Bolt 25 N.m 18 lb ft
Engine Control Module (ECM) Bracket Bolts 10 N.m 89 lb in
Engine Coolant Temperature (ECT) Sensor 20 N.m 15 lb ft
Engine Wiring Harness Retaining Nut 5.5 N.m 49 lb in
EVAP Canister Purge Solenoid Bolt 10.5 N.m 93 lb in
Front End Diagonal Brace Bolt 25 N.m 18 lb ft
Fuel Fill Hose Clamp 2.5 N.m 22 lb in
Fuel Fill Pipe Bracket Nut 10 N.m 89 lb in
Fuel Fill Pipe Ground Strap Bolt 10 N.m 89 lb in
Fuel Pipe Bracket Nut 10 N.m 89 lb in
Fuel Rail Bolt 10 N.m 89 lb in
Fuel Rail Crossover Pipe Retainer Clip Attaching Screw 3.8 N.m 34 lb in
Fuel Return Pipe Attaching Screw 5 N.m 44 lb in
Fuel Tank Shield Bolt 25 N.m 18 lb ft
Fuel Tank Strap Bolt 32 N.m 24 lb ft
Heated Oxygen Sensor (HO2S) 42 N.m 31 lb ft
Ignition Coil Bolt 8 N.m 71 lb in
Knock Sensor (KS) 20 N.m 15 lb ft
Mass Airflow/Intake Air Temperature (MAF/IAT) Sensor Clamp 7 N.m 62 lb in
Spark Plug
  • New Cylinder Heads
 20 N.m 15 lb ft
  • Used Cylinder Heads
 15 N.m 11 lb ft
Throttle Actuator Control (TAC) Module Bracket Nut 9 N.m 80 lb in
Throttle Body Bolt 10 N.m 89 lb in
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.