SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSISUZU2006ASCENDER S, 4.2 S, 4WDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 379 (WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT VIEWS & CONNECTOR END VIEWS)COMPONENT CONNECTOR END VIEWSBODY CONTROL MODULE (BCM) X1
2006 Isuzu Ascender S, 4.2 S, 4WD

Body Control Module (BCM) X1

2006 Isuzu Ascender S, 4.2 S, 4WDSECTION Body Control Module (BCM) X1
WARNING: This page is about a different car, the 2008 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Body Control Module (BCM) X1 Connector End View
GM73156Courtesy of GENERAL MOTORS CORP.
Body Control Module (BCM) X1

Pin Wire Circuit Function
A1 - - Not Used
A2 0.35 WH 2282 Headlamp Washer Relay Control (CE4)
A3 0.35 OG 1140 Battery Positive Voltage
A4 0.35 BK/WH 1969 Headlamp High Beam Relay Control
A5 0.35 PK/WH 1970 Headlamp Low Beam Relay Control
A6 0.35 PK 5363 Inclination Sensor Low Reference (BAE)
A7-A11 - - Not Used
A12 0.35 WH 278 Ambient Light Sensor Signal
B1 0.35 L-GN 1037 Class 2 Serial Data
B2 0.35 BK 279 Ambient Light Sensor Low Reference
B3 0.35 L-GN 2270 Rear Window Washer Relay Control
B4 0.35 GY/BK 2226 Instrument Panel Lamps Dimmer Switch Low Reference
B5 0.35 GY 705 5-Volt Reference
B6 0.35WH 2283 12-Volt Reference
B7 0.35 OG/BK 2090 Courtesy Lamps Supply Voltage
B8 0.35 L-GN 1011 Remote Radio Control Signal (STW)
B9 0.35 GY 391 Rear Window Wiper Switch Signal
B10 0.35 YE 1836 Security System Sensor Signal (w/o BAE)
B11 0.35 GY 2521 Right Sunload Sensor Signal (CJ2)
B12 0.35 L-BU/BK 2519 Left Sunload Sensor Signal (CJ2)
Connector Part Information 
  • OEM: 12110088
  • Service: 15306210
  • Description: 24-Way F Micro-Pack 100 Series (GY)
Terminal Part Information 
  • Pins: A2-A6, A12, B1-B12
  • Terminal/Tray: 12146447/3
  • Core/Insulation Crimp: E/C
  • Release Tool/Test Probe: 12031876-1/J-35616-6 (BN)
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.