Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSISUZU1997OASIS SREPAIR AND DIAGNOSISSUSPENSIONWHEEL ALIGNMENT SPECIFICATIONS & ADJUSTMENT PROCEDURESTORQUE SPECIFICATIONS
1997 Isuzu Oasis S
Torque Specifications
1997 Isuzu Oasis SSECTION Torque Specifications
TORQUE SPECIFICATIONS
| Application | Ft. Lbs (N.m) | ||
|---|---|---|---|
| Accord | |||
| Radius Rod Flange Bolts | 119 (162) | ||
| Radius Rod Lock Nut | |||
| 1997 | 32 (44) | ||
| 1998 | 40 (54) | ||
| Rear Control Arm Adjusting Bolt Lock Nuts | 40 (54) | ||
| Spindle Nut | |||
| Front | 181 (245) | ||
| Rear | 134 (181) | ||
| Tie Rod Lock Nut | 33 (45) | ||
| Wheel Lug Nuts | 80 (108) | ||
| Civic & Civic Del Sol | |||
| Rear Control Arm Adjusting Bolt | 48 (65) | ||
| Spindle Nut | 136 (185) | ||
| Tie Rod Lock Nut | 41 (55) | ||
| Wheel Lug Nuts | 80 (108) | ||
| CR-V | |||
| Rear Control Arm Adjusting Bolt | 48 (65) | ||
| Spindle Nut (Front) | 181 (245) | ||
| Tie Rod Lock Nut | 41 (55) | ||
| Wheel Lug Nuts | 80 (108) | ||
| Odyssey | |||
| Radius Rod Flange Bolts | 76 (103) | ||
| Radius Rod Lock Nut | 40 (54) | ||
| Rear Toe Adjusting Bolt Lock Nut | 40 (54) | ||
| Spindle Nut (Front) | 181 (245) | ||
| Tie Rod Lock Nut | 33 (45) | ||
| Wheel Lug Nuts | 80 (108) | ||
| Prelude | |||
| On Non Active Torque Transfer System (ATTS) Models | |||
| Radius Rod Lock Nut | 40 (54) | ||
| Radius Rod Flange Bolts | 80 (108) | ||
| On Active Torque Transfer System (ATTS) Models | |||
| Radius Rod Flange Nut | 25 (34) | ||
| Radius Rod Flange Bolt | 47 (64) | ||
| Rear Toe Adjusting Bolt Lock Nut | 40 (54) | ||
| Spindle Nut | 181 (245) | ||
| Tie Rod Lock Nut | 33 (45) | ||
| Wheel Lug Nuts | 80 (108) | ||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.