SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSINFINITI2019Q70 3.7 LUXE, AWDREPAIR AND DIAGNOSISENGINE PERFORMANCETESTING & DIAGNOSISENGINE CONTROL SYSTEM (3.7L) (DTC/CIRCUIT DIAGNOSIS) (8 OF 9)DTC/CIRCUIT DIAGNOSISDTC P2271: O2 SENSORDTC DESCRIPTIONDTC CONFIRMATION PROCEDURE
2019 Infiniti Q70 3.7 Luxe, AWD

DTC Confirmation Procedure

2019 Infiniti Q70 3.7 Luxe, AWDSECTION DTC Confirmation Procedure
  1. INSPECTION START 

    Do you have CONSULT?

    Do you have CONSULT?

    YES

    GO TO 2.

    NO

    GO TO 5.

  2. PRECONDITIONING 

    If DTC confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

    1. Turn ignition switch OFF and wait at least 10 seconds.
    2. Turn ignition switch ON.
    3. Turn ignition switch OFF and wait at least 10 seconds.

    TESTING CONDITION:

    For better results, perform "DTC WORK SUPPORT" at a temperature of 0 to 30 deg.C (32 to 86 deg.F).

    GO TO 3.

  3. PERFORM DTC CONFIRMATION PROCEDURE 

    SYMBOL With CONSULT

    1. Turn ignition switch ON and select "DATA MONITOR" mode with CONSULT.
    2. Start engine and warm it up to the normal operating temperature.
    3. Turn ignition switch OFF and wait at least 10 seconds.
    4. Turn ignition switch ON.
    5. Turn ignition switch OFF and wait at least 10 seconds.
    6. Start engine and keep the engine speed between 3, 500 and 4, 000 RPM for at least 1 minute under no load.
    7. Let engine idle for 1 minute.
    8. Make sure that "COOLAN TEMP/S" indicates more than 70 deg.C (158 deg.F).

      If not, warm up engine and go to next step when "COOLAN TEMP/S" indication reaches 70 deg.C (158 deg.F).

    9. Open engine hood.
    10. Select "HO2S2 (B1) P1147" (for DTC P2271) of "HO2S2" in "DTC WORK SUPPORT" mode with CONSULT.
    11. Start engine and follow the instruction of CONSULT display.
      NOTE: It will take at most 10 minutes until "COMPLETED" is displayed.
    12. Touch "SELF-DIAG RESULTS".

    Which is displayed on CONSULT screen?

    OK

    INSPECTION END

    NG

    Go to Diagnosis Procedure .

    CAN NOT BE DIAGNOSED

    GO TO 4.

  4. PERFORM DTC CONFIRMATION PROCEDURE AGAIN 
    1. Turn ignition switch OFF and leave the vehicle in a cool place (soak the vehicle).
    2. Perform DTC confirmation procedure again.

    GO TO 3.

  5. PERFORM COMPONENT FUNCTION CHECK 

    Perform component function check. Refer to Component Function Check .

    NOTE: Use component function check to check the overall function of the heated oxygen sensor 2 circuit. During this check, a 1st trip DTC might not be confirmed.

    Is the inspection result normal?

    YES

    INSPECTION END

    NO

    Go to Diagnosis Procedure .

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.