Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSINFINITI2008EX35 AWD V6-3.5L (VQ35HR)REPAIR AND DIAGNOSISACCESSORIES AND OPTIONAL EQUIPMENTCOLLISION AVOIDANCE AND PARKING ASSIST SYSTEMSTESTING AND INSPECTIONSCAN TOOL TESTING AND PROCEDURESLANE DEPARTURE PREVENTION/WARNING SYSTEMSCONSULT-III FUNCTION
2008 Infiniti EX35 AWD V6-3.5L (VQ35HR)
CONSULT-III Function
2008 Infiniti EX35 AWD V6-3.5L (VQ35HR)SECTION CONSULT-III Function
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)]
CONSULT-III Function
FUNCTION
WORK SUPPORT
SELF DIAGNOSTIC RESULT
Operation Procedure
Before performing the self-diagnosis, start engine and drive vehicle at 30 km/h (19 MPH) or more for approximately 1 minute.
Display Item List
Refer to BRC-95, "DTC No. Index".
How to Erase Self-diagnosis Results
After erasing DTC memory, start the engine and drive the vehicle at 30 km/h (19 MPH) or more for approximately 1 minute as the final inspection, and make sure that the ABS warning lamp, VDC OFF indicator lamp, SLIP indicator lamp and brake warning lamp turn OFF.
CAUTION: If memory cannot be erased, perform applicable diagnosis.
NOTE:
- When the wheel sensor malfunctions, after inspecting the wheel sensor system, ABS warning lamp, VDC OFF indicator lamp, SLIP indicator lamp and brake warning lamp will not turn OFF even when the system is normal unless the vehicle is driven at approximately 30 km/h (19 MPH) or more for approximately 1 minute.
- Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or in case of brake fluid level switch operation (when brake fluid is insufficient).
- VDC OFF switch should not stay in "ON" position.
DATA MONITOR
ACTIVE TEST
CAUTION:
- Do not perform active test while driving vehicle.
- Make sure to completely bleed air from brake system.
- The active test cannot be started when ABS warning lamp, VDC OFF indicator lamp, SLIP indicator lamp and brake warning lamp are ON.
- ABS warning lamp, VDC OFF indicator lamp, SLIP indicator lamp and brake warning lamp are ON during active test.
- Erase memory of ICC system after implementing active test. Refer to CCS-24, "CONSULT-III Function (ICC)". CONSULT-III Function (ICC)
- Erase memory of the lane camera unit after implementing active test. Refer to CCS-130, "CONSULT-III Function (LANE CAMERA)". CONSULT-III Function (LANE CAMERA)
NOTE:
- When active test is performed while depressing the pedal, the pedal depression amount will change. This is normal. (Only solenoid valve and ABS motor.)
- "TEST IS STOPPED" is displayed 10 seconds after operation start.
- After "TEST IS STOPPED" is displayed, to perform test again.
Test Item
ABS SOLENOID VALVE
- Touch "Up", "Keep" and "Down". Then use screen monitor to check that solenoid valve operates as shown in the table below.
ABS SOLENOID VALVE (ACT)
- Touch "Up", "ACT UP" and "ACT KEEP". Then use screen monitor to check that solenoid valve operates shown in the table below.
ABS MOTOR
- Touch "On" and "Off" on screen. Make sure motor relay and actuator relay operates as shown in table below.
ECU IDENTIFICATION
ABS actuator and electric unit (control unit) part number can be read.
CONSULT-III Function
FUNCTION
WORK SUPPORT
SELF DIAGNOSTIC RESULT
Operation Procedure
Before performing the self-diagnosis, start engine and drive vehicle at 30 km/h (19 MPH) or more for approximately 1 minute.
Display Item List
Refer to BRC-95, "DTC No. Index".
How to Erase Self-diagnosis Results
After erasing DTC memory, start the engine and drive the vehicle at 30 km/h (19 MPH) or more for approximately 1 minute as the final inspection, and make sure that the ABS warning lamp, VDC OFF indicator lamp, SLIP indicator lamp and brake warning lamp turn OFF.
CAUTION: If memory cannot be erased, perform applicable diagnosis.
NOTE:
- When the wheel sensor malfunctions, after inspecting the wheel sensor system, ABS warning lamp, VDC OFF indicator lamp, SLIP indicator lamp and brake warning lamp will not turn OFF even when the system is normal unless the vehicle is driven at approximately 30 km/h (19 MPH) or more for approximately 1 minute.
- Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or in case of brake fluid level switch operation (when brake fluid is insufficient).
- VDC OFF switch should not stay in "ON" position.
DATA MONITOR
Display Item List - Data Monitor (Part 1):
Display Item List - Data Monitor (Part 2):
Display Item List - Data Monitor (Part 3):
ACTIVE TEST
CAUTION:
- Do not perform active test while driving vehicle.
- Make sure to completely bleed air from brake system.
- The active test cannot be started when ABS warning lamp, VDC OFF indicator lamp, SLIP indicator lamp and brake warning lamp are ON.
- ABS warning lamp, VDC OFF indicator lamp, SLIP indicator lamp and brake warning lamp are ON during active test.
- Erase memory of ICC system after implementing active test. Refer to CCS-24, "CONSULT-III Function (ICC)". CONSULT-III Function (ICC)
- Erase memory of the lane camera unit after implementing active test. Refer to CCS-130, "CONSULT-III Function (LANE CAMERA)". CONSULT-III Function (LANE CAMERA)
NOTE:
- When active test is performed while depressing the pedal, the pedal depression amount will change. This is normal. (Only solenoid valve and ABS motor.)
- "TEST IS STOPPED" is displayed 10 seconds after operation start.
- After "TEST IS STOPPED" is displayed, to perform test again.
Test Item
ABS SOLENOID VALVE
- Touch "Up", "Keep" and "Down". Then use screen monitor to check that solenoid valve operates as shown in the table below.
ABS SOLENOID VALVE (ACT)
- Touch "Up", "ACT UP" and "ACT KEEP". Then use screen monitor to check that solenoid valve operates shown in the table below.
ABS MOTOR
- Touch "On" and "Off" on screen. Make sure motor relay and actuator relay operates as shown in table below.
ECU IDENTIFICATION
ABS actuator and electric unit (control unit) part number can be read.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.