SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSINFINITI2006FX35 AWDREPAIR AND DIAGNOSISACCESSORIES & EQUIPMENTINTERIOR/ILLUMINATION LIGHTSLIGHTING SYSTEMINTERIOR ROOM LAMPMAP LAMP CONTROL DOES NOT OPERATE
2006 Infiniti FX35 AWD

Map Lamp Control Does Not Operate

2006 Infiniti FX35 AWDSECTION Map Lamp Control Does Not Operate
  1. CHECK EACH SWITCH 

    Select "BCM" on CONSULT-II. With "INT LAMP" data monitor to make sure switches listed in display item list turn ON-OFF linked with switch operation. Refer to "DISPLAY ITEM LIST " for switches and their functions.

    OK or NG 

    OK : GO TO 2.

    NG : Inspect malfunctioning switch system.

    Fig 1: Inspecting Malfunctioning Switch System
    G04078377Courtesy of NISSAN MOTOR CO., U.S.A.
  2. ACTIVE TEST 
    1. Select "BCM" on CONSULT-II. Select "INT LAMP" active test.
    2. When map lamp switch is in DOOR position, use active test to make sure map lamp operates.

      Map lamp should operate. 

      Fig 2: Displaying Active Test
      G04078378Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK : Replace BCM. Refer to "REMOVAL AND INSTALLATION OF BCM ".

    NG : GO TO 3.

  3. CHECK MAP LAMP INPUT 
    1. Turn ignition switch OFF.
    2. Check voltage between map lamp harness connector R52 terminal 2 and ground.

      2 - Ground : Battery voltage. 

      Fig 3: Identifying Voltage Between Map Lamp Harness Connector R52 Terminal 2
      G04078379Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK : GO TO  6.

    NG : GO TO 4.

  4. CHECK MAP LAMP 
    1. Disconnect map lamp connector.
    2. Check continuity between map lamp.
    CONNECTOR SPECIFICATION

    Map lamp Condition Continuity
    2 3 Map lamp switch is DOOR. Yes
    Map lamp switch is OFF. No
    Fig 4: Identifying Continuity Between Map Lamp
    G04078380Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK : GO TO 5.

    NG : Replace Map lamp.

  5. CHECK MAP LAMP CIRCUIT 
    1. Disconnect BCM connector.
    2. Check continuity between BCM harness connector M4 terminal 41 and map lamp harness connector R52 terminal 3.

      41 - 3 : Continuity should exist. 

    OK or NG 

    OK : Replace BCM if map lamp does not work after setting the connector again. Refer to "REMOVAL AND INSTALLATION OF BCM ".

    NG : Repair harness or connector.

    Fig 5: Identifying Continuity Between BCM Harness Connector M4 Terminal 41 And Map Lamp Harness Connector R52 Terminal
    G04078381Courtesy of NISSAN MOTOR CO., U.S.A.
  6. CHECK MAP LAMP CIRCUIT 
    1. Disconnect BCM connector and map lamp connector.
    2. Check continuity between BCM harness connector M4 terminal 48 and map lamp harness connector R52 terminal 2.

      48 - 2 : Continuity should exist. 

    OK or NG 

    OK : Replace BCM if map lamp does not work after setting the connector again. Refer to "REMOVAL AND INSTALLATION OF BCM ".

    NG : Repair harness or connector.

    Fig 6: Identifying Continuity Between BCM Harness Connector M4 Terminal 48 And Map Lamp Harness Connector R52 Terminal
    G04078382Courtesy of NISSAN MOTOR CO., U.S.A.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.