Safety Warning

DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.

SYS.OK|MANUAL.DB● LIVE

HOMESERVICE MANUALSINFINITI2006FX35 AWDREPAIR AND DIAGNOSISACCESSORIES & EQUIPMENTINFOTAINMENTAUDIO, VISUAL, NAVIGATION & TELEPHONE SYSTEMNAVIGATION SYSTEMTINT IS STRANGE FOR THE RGB IMAGE (ONLY NAVI SCREEN)

2006 Infiniti FX35 AWD

Tint Is Strange for The RGB Image (Only NAVI Screen)

2006 Infiniti FX35 AWDSECTION Tint Is Strange for The RGB Image (Only NAVI Screen)

Symptom: Tint of map screen is strange. (Status screen for audio and A/C, TRIP screen and FUEL ECONOMY screen are normal.)

CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit and display unit connectors.
3. Check the malfunctioning circuit according to the symptoms.
- Light blue (Cyan) tinged screen
  Check continuity between NAVI control unit harness connector (A) B207 terminal 44 and display control unit harness connector (B) M76 terminal 44.
  
  44 - 44 : Continuity should exist.
  
  Check continuity between NAVI control unit harness connector (A) B207 terminal 44 and ground.
  
  44 - Ground : Continuity should not exist.
  
  Fig 1: Identifying Continuity Between NAVI Control Unit Harness Connector (A) B207 Terminal 44 And Ground
  Courtesy of NISSAN MOTOR CO., U.S.A.
- Purple (Magenta) tinged screen
  Check continuity between NAVI control unit harness connector (A) B207 terminal 45 and display control unit harness connector (B) M76 terminal 46.
  
  45 - 46 : Continuity should exist.
  
  Check continuity between NAVI control unit harness connector (A) B207 terminal 45 and ground.
  
  45 - Ground : Continuity should not exist.
  
  Fig 2: Identifying Continuity Between NAVI Control Unit Harness Connector (A) B207 Terminal 45 And Ground
  Courtesy of NISSAN MOTOR CO., U.S.A.
- Yellow tinged screen
  Check continuity between NAVI control unit harness connector (A) B207 terminal 46 and display control unit harness connector (B) M76 terminal 48.
  
  46 - 48 : Continuity should exist.
  
  Check continuity between NAVI control unit harness connector (A) B207 terminal 46 and ground.
  
  46 - Ground : Continuity should not exist.
  
  Fig 3: Identifying Continuity Between NAVI Control Unit Harness Connector (A) B207 Terminal 46 And Ground
  Courtesy of NISSAN MOTOR CO., U.S.A.
OK or NG

OK : GO TO 2.

NG : Repair harness or connector.
CHECK RGB SIGNAL
1. Connect NAVI control unit and display control unit connectors.
2. Turn ignition switch ON.
3. Start Confirmation/Adjustment (Navigation) mode. Refer to "CONFIRMATION/ADJUSTMENT MODE ".
4. Display color bar by selecting "Color Spectrum bar" on Display Diagnosis screen. Refer to "DISPLAY DIAGNOSIS ".
5. Check the malfunctioning circuit according to the symptoms.
- Light blue (Cyan) tinged screen
  Check voltage waveform between NAVI control unit harness connector B207 terminal 44 and ground with CONSULT-II or oscilloscope.
  
  44 - Ground:
  
  Fig 4: Identifying Voltage Waveform
  Courtesy of NISSAN MOTOR CO., U.S.A.

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready Tools Free Quote Check Quote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

• You smell fuel, burning insulation, or see smoke.
• Brakes feel soft, pull hard to one side, or make grinding noises.
• The engine overheats, stalls repeatedly, or misfires under load.
• You are missing required tools, torque specs, or safe lifting equipment.
• You are not confident in the next step or safety outcome.