Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHYUNDAI2022SANTA CRUZ SEL, FWDREPAIR AND DIAGNOSISBRAKESTRACTION CONTROLABS/ESC DIAGNOSIS (2 OF 4)
2022 Hyundai Santa Cruz SEL, FWD
Abs/ESC Diagnosis (2 Of 4)
2022 Hyundai Santa Cruz SEL, FWDSECTION Abs/ESC Diagnosis (2 Of 4)
- DTC C1501-93: Switch Failure
- DTC C1503-01: TCS Switch Error
- DTC C1520-01: Clutch Switch
- DTC C1520-02: Clutch Switch
- DTC C1526-01: Down Hill Brake Control (DBC) Switch Error
- DTC C1527-01: Reverse Gear Signal Error
- DTC C1539-01: In Gear Switch Error
- DTC C1542-01: Brake Circuit Error
- DTC C1604-04: ECU Hardware Error
- DTC C1604-96: ECU Hardware Error
- DTC C160E-08: P-CAN Bus OFF
- DTC C160E-88: P-CAN Bus OFF
- DTC C1611-08: CAN Time-Out EMS
- DTC C1612-08: CAN Time-Out TCU
- DTC C1613-4A: CAN Signal Error EMS
- DTC C1613-82: CAN Signal Error EMS
- DTC C1613-83: CAN Signal Error EMS
- DTC C1613-86: CAN Signal Error EMS
- DTC C1613-87: CAN Signal Error EMS
- DTC C1616-08: C-CAN Bus OFF
- DTC C1616-88: C-CAN Bus OFF
- DTC C1623-08: CAN Time-Out Steering Angle Sensor
- DTC C1627-08: CAN Time-Out 4WD
- DTC C1628-08: CAN Time-Out Cluster
- DTC C162A-87: Cluster for DMIC Communication Error
- DTC C162B-87: ECS for ICSC Communication Error
- DTC C162E-04: IVSS SW Execution Time Failure
- DTC C162F-24: CAN Signal Failure 4WD11
- DTC C162F-29: CAN Signal Failure 4WD11
- DTC C162F-82: CAN Signal Failure 4WD11
- DTC C162F-83: CAN Signal Failure 4WD11
- DTC C162F-87: CAN Signal Failure 4WD11
- DTC C1638-82: SCC Communication Error
- DTC C1638-83: SCC Communication Error
- DTC C1638-86: SCC Communication Error
- DTC C1638-87: SCC Communication Error
- DTC C1643-08: CAN Time-Out Yaw Rate & G Sensor
- DTC C1646-82: CAN Signal Error TCU
- DTC C1646-83: CAN Signal Error TCU
- DTC C1646-86: CAN Signal Error TCU
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.