Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHYUNDAI2022SANTA CRUZ SEL, FWDREPAIR AND DIAGNOSIS (SINGLE PAGE)DRIVELINES & AXLESAXLE SHAFTSDRIVESHAFT AND AXLE - GENERAL INFORMATIONSPECIAL SERVICE TOOLS
2022 Hyundai Santa Cruz SEL, FWD
Special Service Tools
2022 Hyundai Santa Cruz SEL, FWDSECTION Special Service Tools
| Tool (Number and Name) | Illustration | Use |
|---|---|---|
| Ball joint remover 09568 - 2J100 | Removal of the tie rod end ball joint. | |
| Lower arm ball joint remover 09568 - 4R100 | Removal of the lower arm ball joint. | |
| Band installer 0K495 - C5000 | Used for installing ear type boot band | |
| Band installer 09495 - 39100 | Used for installing hook type boot band | |
| Differential bearing remover 09501 - C9200 |
Used for removal of differential gear bearing | |
| Differential assembly working stand base 09501 - C9231 |
Used for working on the differential carrier assembly (Use with 0K530 - P2500, 0K501 - P2232) | |
| Rear differential assembly working stand adapter 0K530 - P2500 | Used for working on the differential carrier assembly (Use with 09501 - C9231, 0K501 - P2232) | |
| Sub support 0K501 - P2232 | Used for working on the differential carrier assembly (Use with 09501 - C9231, 0K530 - P2500) |
|
| Bearing remover 09501 - C9310 | Used for removal of the bearing (Use with 09452 - 2E000) | |
| Bearing remover 09452 - 2E000 | Used as main body when removing the bearing (Use with 09501 - C9310) | |
| Bearing race remover (Main body) 09501 - C9140 |
Used for removal ofthe bearing race (Main body only) | |
| Bearing race remover 09501 - C9320 | Used for removal of the outside bearing race | |
| Bearing race remover 09501 - C9330 | Used for removal of the inside bearing race | |
| Rear differential bearing installer 0K530 - P2300 | Used for installing the differential gear bearing | |
| Rear differential bearing installer 0K530 - P2200 | Used for installing the pinion bearing race | |
| Pinion bearing race installer 09501 - C9340 | Removal & Installation of the differential assembly working stand. | |
| Pinion oil seal installer 0K530 - P2100 | Used for installing the pinion oil seal (Use with 09231 - H1100) | |
| Differential oil seal installer 09501 - C9190 |
Used for installing differential case side oil seal (Use with 09231 - H1100) | |
| Handle 09231 - H1100 | Using with 0K530 - P2100, 09501 - C9190 | |
| Backlash measurement supporter 0K530 - P2400 |
Used to measure the backlash |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.