SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHYUNDAI2014GENESIS 3.8REPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTANTI-THEFT SYSTEMSIMMOBILIZER SYSTEMTROUBLESHOOTINGDIAGNOSIS OF IMMOBILIZER FAULTS
2014 Hyundai Genesis 3.8

Diagnosis Of Immobilizer Faults

2014 Hyundai Genesis 3.8SECTION Diagnosis Of Immobilizer Faults
  • Communication between the ECM and the SMARTRA.
  • Function of the SMARTRA and the transponder.
  • Data (stored in the ECM related to the immobilizer function.

The following table shows the assignment of immobilizer related faults to each type:

Immobilizer Related Faults Fault types Diagnostic codes
PCM (ECM) fault
  1. Non-Immobilizer-EMS connected to an Immobilizer
 P1610
Transponder key fault
  1. Transponder not in password mode
  2. Transponder transport data has been changed.
 P1674
(Transponder status error)
Transponder key fault
  1. Transponder programming error
 P1675
(Transponder programming error)
SMARTRA fault
  1. Invalid message from SMARTRA to PCM (ECM)
 P1676
(SMARTRA message error)
SMARTRA fault
  1. Virgin SMARTRA at learnt EMS
  2. Neutral SMARTRA at learnt EMS
  3. Incorrect the Authentication of EMS and SMARTRA
  4. Locking of SMARTRA
 P169A
(SMARTRA Authentication fail)
SMARTRA fault
  1. No response from SMARTRA
  2. Antenna coil error
  3. Communication line error (Open/Short etc.)
  4. Invalid message from SMARTRA to PCM (ECM)
 P1690
(SMARTRA no response)
Antenna coil fault
  1. Antenna coil open/short circuit
 P1691
(Antenna coil error)
Immobilizer indicator lamp fault
  1. Immobilizer indicator lamp error (Cluster)
 P1692
(Immobilizer lamp error)
Transponder key fault
  1. Corrupted data from transponder
  2. More than one transponder in the magnetic field (Antenna coil)
  3. No transponder (Key without transponder) in the magnetic field (Antenna coil)
 P1693
(Transponder no response error/invalid response)
PCM (ECM) fault
  1. Request from PCM (ECM) is invalid

    (Protocol layer violation-Invalid request, check sum error etc.)

 P1694
(PCM (ECM) message error)
PCM (ECM) internal permanent memory (EEPROM) fault
  1. PCM (ECM) internal permanent memory (EEPROM) fault
  2. Invalid write operation to permanent memory (EEPROM)
 P1695
(PCM (ECM) memory error)
Invalid key fault
  1. Virgin transponder at PCM (ECM) status "Learnt" Learnt (Invalid) Transponder at PCM (ECM) status "Learnt" (Authentication fail)
 P1696
(Authentication fail)
Hi-Scan fault
  1. Hi-Scan message error
 P1697
Locked by timer
  1. Exceeding the maximum limit of Twice IGN ON ( 32 times)
 P1699
(Twice IG ON over trial)
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.