SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHYUNDAI2014AZERA BASEREPAIR AND DIAGNOSIS (SINGLE PAGE)BODY & FRAMEDOOR LOCKSKEYLESS ENTRY & BURGLAR ALARMKEYLESS ENTRY AND BURGLAR ALARMDESCRIPTION AND OPERATIONFUNCTION DESCRIPTIONSTATE DESCRIPTIONDISARM
2014 Hyundai Azera Base

State Description: Disarm

2014 Hyundai Azera BaseSECTION Disarm
  1. DISARM to DISARM
    CONDITION 1 DESCRIPTION

    State Description
    Initial Condition
    • DISARM STATE
    • Key Out state (Key Off)
    • Any Door is Open (Any Door Open On)
    Event Unlock by RKE (RKE Unlock Off → On)
    Action
    • DISARM Flashing (Disarm Flasher On)
    • DISARM Buzzer Activation (Disarm Buzzer On)
    • State does not changed
    CONDITION 2 DESCRIPTION

    State Description
    Initial Condition
    • DISARM STATE
    • Any Door is Open (Any Door Open On)
    Event Unlock by SMK (Passive Access Unlock Off→ On)
    Action
    • DISARM Flashing (Disarm Flasher On)
    • DISARM Buzzer Activation (Disarm Buzzer On)
    • State does not changed
    CONDITION 3 DESCRIPTION

    State Description
    Initial Condition
    • DISARM STATE
    Event Key On state (Key On)
    Action
    • Security IND is Off (Security IND Off).
    • State does not changed
    CONDITION 4 DESCRIPTION

    State Description
    Initial Condition
    • DISARM STATE
    Event Key Off state (Key Off On)
    Action
    • Security IND is Blinking (Security IND Blinking; 0.32sec: On/2sec: Off).
    • State does not changed
  2. ARMWAIT to DISARM
    CONDITION 1 DESCRIPTION

    State Description
    Initial Condition
    • ARMWAIT STATE
    Event
    1. Key In (Key In On) or
    2. Fob In (Fob In On) or
    3. Any Door is Open (Any Door Open On) or
    4. Hood is Open (Hood SW On) or
    5. Trunk is Open (Trunk Status On) or
    6. Any Door is Unlock (Any Door Unlock On)
    Action
    CONDITION 2 DESCRIPTION

    State Description
    Initial Condition
    • ARMWAIT STATE
    • Mechanical key ARM/DISARM Option is enable (MECH Opt On)
    Event Unlock by Mechanical Key (DRV Key Unlock Off → On)
    Action
    CONDITION 3 DESCRIPTION

    State Description
    Initial Condition
    • ARMWAIT STATE
    Event
    1. Authenticate by Immobilizer System (TP_AUTH On) or
    2. Authenticate by SMK (PIC_AUTH On) or
    3. Pre-Authenticate by valid Fob (TP FeedBack On)
    Action
  3. ARM to DISARM
    CONDITION 1 DESCRIPTION

    State Description
    Initial Condition
    • ARM STATE
    Event
    1. Authenticate by Immobilizer System (TP AUTH On) or
    2. Authenticate by SMK (PIC AUTH On) or
    3. Pre-Authenticate by valid Fob (TP FeedBack On)
    Action
    CONDITION 2 DESCRIPTION

    State Description
    Initial Condition
    • ARM STATE
    • No China Option (China Option Off)
    Event Key In and IGN1 On and IGN2 On (Key IGN On)
    Action
    CONDITION 3 DESCRIPTION

    State Description
    Initial Condition
    • ARM STATE
    • Mechanical key ARM/DISARM Option is enable (MECH Opt On)
    Event Unlock by Mechanical Key (DRV Key Unlock Off → On)
    Action
  4. ARM HOLD to DISARM
    CONDITION 1 DESCRIPTION

    State Description
    Initial Condition
    • ARMHOLD STATE
    Event
    1. Authenticate by Immobilizer System (TP AUTH On) or
    2. Authenticate by SMK (PIC AUTH On) or
    3. Pre-Authenticate by valid Fob (TP FeedBack On)
    Action
    CONDITION 2 DESCRIPTION

    State Description
    Initial Condition
    • ARMHOLD STATE
    • No China Option (China Option Off)
    Event Key In and IGN1 On and IGN2 On (Key IGN On)
    Action
    CONDITION 3 DESCRIPTION

    State Description
    Initial Condition
    • ARMHOLD STATE
    • Mechanical key ARM/DISARM Option is enable (MECH Opt On)
    Event Unlock by Mechanical Key (DRV Key Unlock Off → On)
    Action
  5. AUTO LOCK TIMER1 to DISARM
    CONDITION 1 DESCRIPTION

    State Description
    Initial Condition
    • AUTOLOCKTIMER1 STATE
    Event
    1. Key In (Key In On) or
    2. Fob In (Fob In On) or
    3. Any Door is Open (Any Door Open On) or
    4. Hood is Open (Hood SW On) or
    5. Trunk is Open (Trunk Status On) or
    6. Authenticate by Immobilizer System (TP AUTH On) or
    7. Authenticate by SMK (PIC AUTH On) or
    8. Pre-Authenticate by valid Fob (TP FeedBack On) or
    9. Lock by RKE/SMK/AutoLock/Mechanical key with option mechanical set but locking failed (Lock Confirm Fail Off → On)
    Action
  6. AUTO LOCK TIMER2 to DISARM
    CONDITION 1 DESCRIPTION

    State Description
    Initial Condition
    • AUTOLOCKTIMER2 STATE
    Event
    1. Key In On (Key In On) or
    2. Fob In (Fob In On) or
    3. Any Door is Open (Any Door Open On) or
    4. Hood is Open (Hood SW On & Hood Open Off) or
    5. Trunk is Open (Trunk Status On & Trunk Open Off) or
    6. Authenticate by Immobilizer System (TP AUTH On) or
    7. Authenticate by SMK (PIC AUTH On) or
    8. Pre-Authenticate by valid Fob (TP FeedBack On) or
    9. Lock by RKE/SMK/AutoLock/Mechanical key with option mechanical set but locking failed (Lock Confirm Fail Off → On)
    Action
    • Hood Open Off
    • Trunk Open Off
    • Auto Lock Off
    • State go to DISARM STATE 
  7. PREARM to DISARM
    CONDITION 1 DESCRIPTION

    State Description
    Initial Condition
    • PREARM STATE
    Event
    1. Key In On (Key In On) or
    2. Fob In (Fob In On) or
    3. Authenticate by Immobilizer System (TP AUTH On) or
    4. Authenticate by SMK (PIC AUTH On) or
    5. Pre-Authenticate by valid Fob (TP FeedBack On) or
    6. All Doors are Close (All Doors Close On) and Hood is Close (Hood SW Off) and Trunk is Close (Trunk Status Off) and Any Door is Unlock (Any Door Unlock On)
    Action
    CONDITION 2 DESCRIPTION

    State Description
    Initial Condition
    • PREARM STATE
    • Any Door is Open (Any Door Open On)
    Event
    1. Unlock by SMK (Passive Access Unlock Off → On) or
    2. Unlock by RKE (RKE Unlock Off → On)
    Action
    • DISARM Flashing (Disarm Flasher On)
    • DISARM Buzzer Activation (Disarm Buzzer On)
    • State go to DISARM STATE 
  8. REARM to DISARM
    CONDITION 1 DESCRIPTION

    State Description
    Initial Condition
    • REARM STATE
    Event
    1. Trunk release by RKE (RKE Trunk Off → On) or
    2. Trunk release by SMK (P TRUNK Off → On) or
    3. Lock by RKE/SMK but Locking is Failed (Lock Confirm Fail Off → On) or
    4. Authenticate by Immobilizer System (TP AUTH On) or
    5. Authenticate by SMK (PIC AUTH On) or
    6. Alternator Input Level is High during 3 sec (Alt L Alarm Release On) or
    7. Pre-Authenticate by valid Fob (TP FeedBack On)
    Action
    • Engine Start Inhibition state is released (Start Inhibition Off)
    • State go to DISARM STATE 
    CONDITION 2 DESCRIPTION

    State Description
    Initial Condition
    • REARM STATE at Non China Option (China Option Off)
    Event Key In On and IGN1 On and IGN2 On during 30sec (Key IGN Alarm Release On)
    Action
    • Engine Start Inhibition state is released (Start Inhibition Off)
    • State go to DISARM STATE 
    CONDITION 3 DESCRIPTION

    State Description
    Initial Condition
    • REARM STATE
    • Mechanical key ARM/DISARM Option is enable (MECH Opt On)
    Event
    1. Unlock by Mechanical Key (DRV Key Unlock Off → On) or
    2. Lock by Mechanical Key but Locking is Failed (Lock Confirm Fail Off→On) or
    3. Trunk Release by Mechanical Key (Trunk Key Unlock SW Off → On)
    Action
    • Engine Start Inhibition state is released (Start Inhibition Off)
    • State go to DISARM STATE 
  9. ALARM to DISARM
    CONDITION 1 DESCRIPTION

    State Description
    Initial Condition
    • ALARM STATE
    Event
    1. Trunk release by RKE (RKE Trunk Off → On) or
    2. Trunk release by SMK (P TRUNK Off → On) or
    3. Lock by RKE/SMK but Locking is Failed (Lock Confirm Fail Off → On) or
    4. Authenticate by Immobilizer System (TP AUTH On) or
    5. Authenticate by SMK (PIC AUTH On) or
    6. Pre-Authenticate by valid Fob (TP FeedBack On) or
    7. Alternator Input Level is High (Alt L On) during 3 sec (Alt L Alarm Release On)
    Action
    • Stop alarm flashing (Alarm Flasher Off)
    • Stop Burglar Alarm Horn (Burglar Alarm Horn Off/Horn Off)
    • Engine Start Inhibition state is released (Start Inhibition Off)
    • State go to DISARM STATE 
    CONDITION 2 DESCRIPTION

    State Description
    Initial Condition
    • ALARM STATE at Non China Option (China Option Off)
    Event Key In and IGN1 On and IGN2 On during 30sec (Key IGN Alarm Release On)
    Action
    • Stop alarm flashing (Alarm Flasher Off)
    • Stop Burglar Alarm Horn (Burglar Alarm Horn Off/Horn Off)
    • Engine Start Inhibition state is released (Start Inhibition Off)
    • State go to DISARM STATE 
    CONDITION 3 DESCRIPTION

    State Description
    Initial Condition
    • ALARM STATE
    • Mechanical key ARM/DISARM Option is enable (MECH Opt On)
    Event
    1. Unlock by Mechanical Key (DRV Key Unlock Off → On) or
    2. Trunk release by Mechanical Key (Trunk Key Unlock SW Off → On) or
    3. Lock by Mechanical Key but Locking is Failed (Lock Confirm Fail Off → On)
    Action
    • Stop alarm flashing (Alarm Flasher Off)
    • Stop Burglar Alarm Horn (Burglar Alarm Horn Off/Horn Off)
    • Engine Start Inhibition state is released (Start Inhibition Off)
    • State go to DISARM STATE 
    CONDITION 4 DESCRIPTION

    State Description
    Initial Condition
    • ALARM STATE
    • Any Door is Open (Any Door Open On)
    Event
    1. Unlock by SMK (Passive Access Unlock Off → On) or
    2. Unlock by RKE (RKE Unlock Off → On)
    Action
    • DISARM Flashing (Disarm Flasher On)
    • DISARM Buzzer Activation (Disarm Buzzer On)
    • Stop alarm flashing (Alarm Flasher Off)
    • Stop Burglar Alarm Horn (Burglar Alarm Horn Off/Horn Off)
    • Engine Start Inhibition state is released (Start Inhibition Off)
    • State go to DISARM STATE 
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.