Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHYUNDAI2013GENESIS COUPE 2.0T PREMIUMREPAIR AND DIAGNOSIS (SINGLE PAGE)ENGINE PERFORMANCESYSTEMENGINE CONTROL SYSTEM (DTC TROUBLESHOOTING) (2 OF 3) - 2.0LDTC INDEX
2013 Hyundai Genesis Coupe 2.0T Premium
DTC Index
2013 Hyundai Genesis Coupe 2.0T PremiumSECTION DTC Index
DTC INDEX
| DTC | Description |
|---|---|
| DTC P0261 | Cylinder 1 Injector Circuit Low |
| DTC P0262 | Cylinder 1 Injector Circuit High |
| DTC P0263 | Cylinder 1 Contribution/Balance |
| DTC P0264 | Cylinder 2 Injector Circuit Low |
| DTC P0265 | Cylinder 2 Injector Circuit High |
| DTC P0266 | Cylinder 2 Contribution/Balance |
| DTC P0267 | Cylinder 3 Injector Circuit Low |
| DTC P0268 | Cylinder 3 Injector Circuit High |
| DTC P0269 | Cylinder 3 Contribution/Balance |
| DTC P0270 | Cylinder 4 Injector Circuit Low |
| DTC P0271 | Cylinder 4 Injector Circuit High |
| DTC P0272 | Cylinder 4 Contribution/Balance |
| DTC P0299 | Turbocharger/Supercharger Underboost |
| DTC P0300 | Random/Multiple Cylinder Misfire Detected |
| DTC P0301 | Cylinder 1-Misfire Detected |
| DTC P0302 | Cylinder 2-Misfire Detected |
| DTC P0303 | Cylinder 3-Misfire Detected |
| DTC P0304 | Cylinder 4-Misfire Detected |
| DTC P0315 | Crankshaft Position System Not Learned |
| DTC P0326 | Knock Sensor 1 Circuit Range/Performance (Bank 1 Or Single Sensor) |
| DTC P0335 | Crankshaft Position Sensor 'A' Circuit |
| DTC P0336 | Crankshaft Position Sensor 'A' Circuit Range/Performance |
| DTC P0340 | Camshaft Position Sensor 'A' Circuit (Single Sensor) |
| DTC P0341 | Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1) |
| DTC P0365 | Camshaft Position Sensor 'B' Circuit Malfunction (Bank 1) |
| DTC P0366 | Camshaft Position Sensor 'B' Circuit Range/Performance (Bank 1) |
| DTC P0420 | Catalyst System Efficiency Below Threshold (Bank 1) |
| DTC P0441 | Evaporative Emission System Incorrect Purge Flow |
| DTC P0442 | Evaporative Emission System-Leak Detected (Small Leak) |
| DTC P0444 | Evaporative Emission System-Purge Control Valve Circuit Open |
| DTC P0445 | Evaporative Emission System-Purge Control Valve Circuit Shorted |
| DTC P0447 | Evaporative Emission System-Vent Control Circuit Open |
| DTC P0448 | Evaporative Emission System-Vent Control Circuit Shorted |
| DTC P0449 | Evaporative Emission System-Vent Valve/Solenoid Circuit |
| DTC P0451 | Evaporative Emission System-Pressure Sensor Range/Performance |
| DTC P0452 | Evaporative Emission System-Pressure Sensor Low Input |
| DTC P0453 | Evaporative Emission System-Pressure Sensor High Input |
| DTC P0454 | Evaporative Emission System-Pressure Sensor/Switch Intermittent |
| DTC P0455 | Evaporative Emission System-Leak Detected (Large Leak) |
| DTC P0456 | Evaporative Emission System-Leak Detected (Very Small Leak) |
| DTC P0461 | Fuel Level Sensor 'A' Circuit Range/Performance |
| DTC P0462 | Fuel Level Sensor 'A' Circuit Low Input |
| DTC P0463 | Fuel Level Sensor 'A' Circuit High Input |
| DTC P0464 | Fuel Level Sensor 'A' Circuit Intermittent |
| DTC P0504 | Brake Switch 'A'/'B' Correlation |
| DTC P0506 | Idle Air Control System-RPM Lower Than Expected |
| DTC P0507 | Idle Air Control System-RPM Higher Than Expected |
| DTC P050A | Cold Start Idle Air Control System Performance |
| DTC P050B | Cold Start Ignition Timing Performance |
| DTC P0532 | A/C Refrigerant Pressure Sensor 'A' Circuit Low Input |
| DTC P0533 | A/C Refrigerant Pressure Sensor 'A' Circuit High Input |
| DTC P0551 | Power Steering Pressure Sensor/Switch Circuit Range/Performance |
| DTC P0560 | System Voltage |
| DTC P0562 | System Voltage Low |
| DTC P0563 | System Voltage High |
| DTC P0564 | Cruise Control Multi-Function Input A Circuit |
| DTC P0605 | Internal Control Module Read Only Memory (ROM) Error |
| DTC P0606 | ECM/PCM Processor |
| DTC P0625 | Generator Field/F Terminal Circuit Low |
| DTC P0626 | Generator Field/F Terminal Circuit High |
| DTC P0630 | VIN Not Programmed Or Incompatible-ECM/PCM |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.