Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHYUNDAI2008ENTOURAGE V6-3.8LREPAIR AND DIAGNOSISRELAYS AND MODULESRELAYS AND MODULES - RESTRAINTS AND SAFETY SYSTEMSAIR BAG CONTROL MODULESERVICE AND REPAIR
2008 Hyundai Entourage V6-3.8L
Air Bag Control Module: Service and Repair
2008 Hyundai Entourage V6-3.8LSECTION Service and Repair
SUPPLEMENTAL RESTRAINT SYSTEM CONTROL MODULE (SRSCM)
REMOVAL
1. Disconnect the negative (-) cable from battery and wait for at least three minutes.
2. Remove ignition key from the vehicle.
3. Disconnect the DAB, PAB, SAB, CAB and BPT connectors.
4. Remove the floor console and heater ducts.
5. Press the lock (1), then pull back the connector lever (2) until it clicks.
6. Disconnect the SRSCM harness connector (A) and (B) from the SRSCM.
7. Remove the SRSCM mounting bolt (A) and nuts (B) from the SRSCM. then remove the SRSCM.
INSTALLATION
1. Disconnect the negative (-) cable from battery and wait for at least three minutes.
2. Remove ignition key from the vehicle.
3. Install the SRSCM with the SRSCM mounting bolt and nuts.
Tightening Torque : 1.0 - 1.4 kgf.m (9.5 - 13.6 Nm, 7.0 - 10.0 lb.ft)
4. Connect the SRSCM harness connector.
5. Install the heater ducts and floor console.
6. Connect the DAB, PAB, SAB, CAB and BPT connectors.
7. Reconnect the battery negative cable.
8. After installing the SRSCM, confirm proper system operation.
- Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.
REMOVAL
1. Disconnect the negative (-) cable from battery and wait for at least three minutes.
2. Remove ignition key from the vehicle.
3. Disconnect the DAB, PAB, SAB, CAB and BPT connectors.
4. Remove the floor console and heater ducts.
5. Press the lock (1), then pull back the connector lever (2) until it clicks.
6. Disconnect the SRSCM harness connector (A) and (B) from the SRSCM.
7. Remove the SRSCM mounting bolt (A) and nuts (B) from the SRSCM. then remove the SRSCM.
INSTALLATION
1. Disconnect the negative (-) cable from battery and wait for at least three minutes.
2. Remove ignition key from the vehicle.
3. Install the SRSCM with the SRSCM mounting bolt and nuts.
Tightening Torque : 1.0 - 1.4 kgf.m (9.5 - 13.6 Nm, 7.0 - 10.0 lb.ft)
4. Connect the SRSCM harness connector.
5. Install the heater ducts and floor console.
6. Connect the DAB, PAB, SAB, CAB and BPT connectors.
7. Reconnect the battery negative cable.
8. After installing the SRSCM, confirm proper system operation.
- Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.