Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHYUNDAI1999ELANTRA WAGON L4-2.0LREPAIR AND DIAGNOSISMAINTENANCEFLUIDSENGINE OILSERVICE AND REPAIR
1999 Hyundai Elantra Wagon L4-2.0L
Engine Oil: Service and Repair
1999 Hyundai Elantra Wagon L4-2.0LSECTION Service and Repair
CAUTION: Be careful not to burn yourself, as the engine oil is hot.
1. Run the engine until it reaches normal operating temperature.
2. Stop the engine.
3. Remove the oil filler cap (on rocker cover) and the drain plug (on the oil pan). Drain the engine oil.
4. Re-install and tighten the drain plug to the specified torque.
Tightening torque:
Drain plug: 35 - 45 Nm (350 - 450 kg.cm, 25 - 33 ft. lbs.)
5. Fill the crankcase with fresh engine oil through the oil filler cap opening.
Capacity:
Dry fill: 4.3 lit (3.91 U.S. qts., 3.25 Imp. qts.)
Drain and refill:
Without oil filter: 3.7 lit (3.91 U.S. qts., 3.25 Imp. qts.)
With oil filter: 4.0 lit (4.23 U.S. qts., 3.51 Imp. qts.)
CAUTION: Do not overfill the crankcase. This will cause oil aeration and loss of oil pressure.
6. Install the oil filler cap.
7. Start and run the engine.
8. Stop the engine and then check the oil level. Add oil if necessary.
1. Run the engine until it reaches normal operating temperature.
2. Stop the engine.
3. Remove the oil filler cap (on rocker cover) and the drain plug (on the oil pan). Drain the engine oil.
4. Re-install and tighten the drain plug to the specified torque.
Tightening torque:
Drain plug: 35 - 45 Nm (350 - 450 kg.cm, 25 - 33 ft. lbs.)
5. Fill the crankcase with fresh engine oil through the oil filler cap opening.
Capacity:
Dry fill: 4.3 lit (3.91 U.S. qts., 3.25 Imp. qts.)
Drain and refill:
Without oil filter: 3.7 lit (3.91 U.S. qts., 3.25 Imp. qts.)
With oil filter: 4.0 lit (4.23 U.S. qts., 3.51 Imp. qts.)
CAUTION: Do not overfill the crankcase. This will cause oil aeration and loss of oil pressure.
6. Install the oil filler cap.
7. Start and run the engine.
8. Stop the engine and then check the oil level. Add oil if necessary.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.