VSA System

2013 Honda CR-V EX, 2.4L Eng VIN 4SECTION VSA System
DTC Detection Item
11 -13 Right-Front Wheel Speed Sensor Circuit Malfunction
12 -11 Right-Front Wheel Speed Sensor Electrical Noise or Intermittent Interruption
-14 Right-Front Wheel Speed Sensor Installation Error
-15 Right-Front Wheel Speed Sensor Installation Error
13 -13 Left-Front Wheel Speed Sensor Circuit Malfunction
14 -11 Left-Front Wheel Speed Sensor Electrical Noise or Intermittent Interruption
-14 Left-Front Wheel Speed Sensor Installation Error
-15 Left-Front Wheel Speed Sensor Installation Error
15 -13 Right-Rear Wheel Speed Sensor Circuit Malfunction
16 -11 Right-Rear Wheel Speed Sensor Electrical Noise or Intermittent Interruption
-14 Right-Rear Wheel Speed Sensor Installation Error
-15 Right-Rear Wheel Speed Sensor Installation Error
17 -13 Left-Rear Wheel Speed Sensor Circuit Malfunction
18 -11 Left-Rear Wheel Speed Sensor Electrical Noise or Intermittent Interruption
-14 Left-Rear Wheel Speed Sensor Installation Error
-15 Left-Rear Wheel Speed Sensor Installation Error
25 -21 Yaw Rate Sensor (Inside of Modulator-Control Unit) Output Signal Malfunction
26 -21 Lateral Acceleration Sensor (Inside of Modulator-Control Unit) Output Signal Malfunction
27 -20 Steering Angle Sensor Internal Circuit Malfunction
-21 Steering Angle Sensor Output Signal Malfunction
28 -21 Longitudinal Acceleration Sensor (Inside of Modulator-Control Unit) Output Signal Malfunction
-22 Longitudinal Acceleration Sensor (Inside of Modulator-Control Unit) Stuck
31 -11 ABS Solenoid Valve Malfunction
32 -11 ABS Solenoid Valve Malfunction
33 -11 ABS Solenoid Valve Malfunction
34 -11 ABS Solenoid Valve Malfunction
35 -11 ABS Solenoid Valve Malfunction
36 -11 ABS Solenoid Valve Malfunction
37 -11 ABS Solenoid Valve Malfunction
38 -11 ABS Solenoid Valve Malfunction
51 -12 Motor Power Source Circuit Malfunction
-13 Motor Drive Circuit Malfunction
-80 Motor Malfunction
52 -11 Motor Stuck OFF
53 -11 Motor Relay Stuck ON
54 -13 Fail-Safe Relay Power Source Malfunction
-14 Fail-Safe Relay Drive Circuit Malfunction
61 -12 Modulator-Control Unit Power Source Circuit (IG) Low Voltage
62 -11 Modulator-Control Unit Power Source Circuit (IG) High Voltage
65 -11 Brake Fluid Level Switch Circuit Malfunction
66 -13 Pressure Sensor Malfunction
-14 Pressure Sensor Sensitivity Malfunction
68 -12 Brake Pedal Position Switch Stuck ON
-13 Brake Pedal Position Switch Circuit Malfunction
71 -80 Abnormal Slip Malfunction
-81 Right-Front Wheel Abnormal Slip Malfunction
-82 Left-Front Wheel Abnormal Slip Malfunction
-83 Right-Rear Wheel Abnormal Slip Malfunction
-84 Left-Rear Wheel Abnormal Slip Malfunction
81 -11 Modulator-Control Unit Internal Circuit Malfunction
-19 Yaw Rate Sensor (Inside of Modulator-Control Unit) Internal Circuit Malfunction
-20 Acceleration Sensor (Inside of Modulator-Control Unit) Internal Circuit Malfunction
83 -11 ECM/PCM (PGM-FI) Malfunction
86 -11 F-CAN Bus-Off Malfunction
-12 F-CAN Communication With ECM/PCM (PGM-FI) Malfunction
-13 F-CAN Communication With PCM (AT/CVT) Malfunction
-14 F-CAN Communication With Gauge Control Module Malfunction
-19 F-CAN Communication With Steering Angle Sensor Malfunction
87 -1 Wheel Speed Sensor Circuit Short to Power
88 -11 Wheel Speed Sensor Noise Malfunction
-12 ABS Activation Time Too Long
91 -1 VSA Activation Time Too Long
121 -11 VSA Solenoid Valve Malfunction
122 -11 VSA Solenoid Valve Malfunction
123 -11 VSA Solenoid Valve Malfunction
124 -11 VSA Solenoid Valve Malfunction
158 -1 ECU Software Update Failure
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.