Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHONDA2009S2000 BASEREPAIR AND DIAGNOSIS (SINGLE PAGE)ENGINE MECHANICALAUXILIARY EMISSION CONTROL SYSTEMSFUEL AND EMISSIONS SYSTEMS
2009 Honda S2000 Base
Fuel And Emissions Systems
2009 Honda S2000 BaseSECTION Fuel And Emissions Systems
- Special Tools
- General Troubleshooting Information
- Intermittent Failures
- Opens and Shorts
- How to Use the HDS (Honda Diagnostic System)
- HDS Clear Command
- Scan Tool Clear Command
- DTC Clear
- ECM Reset
- Crank (CKP) Pattern Clear/Crank (CKP) Pattern Learn
- How to End a Troubleshooting Session (required after any troubleshooting)
- How to Troubleshoot Circuits at the ECM
- Updating the ECM
- Substituting the ECM
- OBD Status
- DTC Troubleshooting Index
- Symptom Troubleshooting Index
- System Description
- Electronic Control System
- ECM Inputs and Outputs at Connector A (31P)
- ECM Inputs and Outputs at Connector B (24P)
- ECM Inputs and Outputs at Connector D (17P)
- ECM Inputs and Outputs at Connector E (31P)
- Vacuum Hose Routing
- Vacuum Distribution
- PGM-FI System
- Notes
- Air Conditioning (A/C) Compressor Clutch Relay
- Air Fuel Ratio (A/F) Sensor
- Barometric Pressure (BARO) Sensor
- Camshaft Position (CMP) Sensor
- Crankshaft Position (CKP) Sensor
- Engine Coolant Temperature (ECT) Sensor 1/Engine Coolant Temperature (ECT) Sensor 2
- Ignition Timing Control
- Injector Timing and Duration
- Intake Air Temperature (IAT) Sensor
- Knock Sensor
- Malfunction Indicator Lamp (MIL) Indication (In relation to Readiness Codes)
- Manifold Absolute Pressure (MAP) Sensor
- Output Shaft (Countershaft) Speed Sensor
- Secondary Heated Oxygen Sensor (Secondary HO2S)
- Electronic Throttle Control System
- Idle Control System
- Fuel Supply System
- Catalytic Converter System
- Positive Crankcase Ventilation (PCV) System
- Evaporative Emission (EVAP) Control System
- Fuel Cap Warning Message
- To make the message go off (with the HDS)
- To make the message go off (without the HDS) ('06-07 models)
- To make the message go off (without the HDS) ('08-09 models)
- Electronic Throttle Control System Diagram
- Evaporative Emission (EVAP) Control Diagram
- How to Set Readiness Codes
- Malfunction Indicator Lamp (MIL) Indication (In relation to Readiness Codes)
- Catalytic Converter Monitor and Readiness Code
- Evaporative Emission (EVAP) Control System Monitor and Readiness Code
- Air Fuel Ratio (A/F) Sensor Monitor and Readiness Code
- Air Fuel Ratio (A/F) Sensor Heater Monitor Readiness Code
- Misfire Monitor and Readiness Code
- Fuel System Monitor and Readiness Code
- Comprehensive Component Monitor and Readiness Code
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.