Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHONDA2009ODYSSEY EX-LREPAIR AND DIAGNOSIS (SINGLE PAGE)ELECTRICALBODY ELECTRICALENGINE ELECTRICAL SERVICE SPECIFICATIONSENGINE ELECTRICAL
2009 Honda Odyssey EX-L
Engine Electrical
2009 Honda Odyssey EX-LSECTION Engine Electrical
ENGINE ELECTRICAL SPECIFICATION
| Item | Measurement | Qualification | Standard or New | Service Limit |
|---|---|---|---|---|
| Ignition coil | Rated voltage | 12V | ||
| Firing order | 1-4-2-5-3-6 | |||
| Spark plug | Type (J35A6, J35A7: '07 model) | NGK:IZFR5K11 | ||
| Type (J35A7: '08-10 models) | NGK:ILZKR7B-11 | |||
| Gap | 1.0-1.1 mm (0.039-0.043 in.) | |||
| Ignition timing | At idle Check the red mark | In N or P | 10° ± 2°BTDC | |
| Drive belt | Tension | Auto-tensioner | ||
| Alternator | Output | At 13.5 V and normal engine temperature | ||
| Coil (rotor) resistance | At 68°F (20°C) | 2.5 Ω | ||
| Slip ring O.D. | 14.4 mm (0.57 in.) | 14.0 mm (0.55 in.) | ||
| Brush length | 10.5 mm (0.41 in.) | 1.5 mm (0.06 in.) | ||
| Brush spring tension | 3.2 N (0.33 kgf, 0.72 lbf) | |||
| Starter (J35A6, J35A7: '07 model) | Output | 1.6 kW | ||
| Commutator mica depth | 0.40-0.50 mm (0.016-0.020 in.) | 0.20 mm (0.008 in.) | ||
| Commutator runout | 0.05 mm (0.002 in.) max. | 0.1 mm (0.004 in.) | ||
| Commutator O.D. | 29.3-29.5 mm (1.15-1.16 in.) | 28.8 mm (1.13 in.) | ||
| Brush length | 15.0-16.0 mm (0.59-0.63 in.) | 9.0 mm (0.35 in.) | ||
| Brush spring tension (new) | 15.7-17.7 N (1.60-1.80 kgf, 3.53--3.98 lbf) | |||
| Starter (J35A7: '08-10 models) | Output | 1.8 kW | ||
| Commutator mica depth | 0.50-0.90 mm (0.020-0.035 in.) | 0.20 mm (0.008 in.) | ||
| Commutator runout | 0.02 mm (0.0008 in.) max. | 0.05 mm (0.002 in.) | ||
| Commutator O.D. | 28.9-29.0 mm (1.138-1.142 in.) | 28.0 mm (1.102 in.) | ||
| Brush length | 15.0-16.0 mm (0.59-0.63 in.) | 9.0 mm (0.35 in.) | ||
| Brush spring tension (new) | 22.3-27.3 N (2.27-2.78 kgf, 5.00--6.13 lbf) | |||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.