SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHONDA2007RIDGELINE RTSREPAIR AND DIAGNOSISACCESSORIES & EQUIPMENTINFOTAINMENTAUDIO SYSTEMSYSTEM DESCRIPTIONCD CHANGER CONNECTOR FOR INPUTS AND OUTPUTS (WITH NAVIGATION SYSTEM)
2007 Honda Ridgeline RTS

CD Changer Connector for Inputs and Outputs (With Navigation System)

2007 Honda Ridgeline RTSSECTION CD Changer Connector for Inputs and Outputs (With Navigation System)

When replacing a CD changer connector, match the wires to the cavities listed in the following tables.

Fig 1: Identifying CD Changer Connectors (With Navigation System)
G05593128Courtesy of AMERICAN HONDA MOTOR CO., INC.
CD CHANGER CONNECTOR FOR INPUTS AND OUTPUTS (WITH NAVIGATION SYSTEM)

Cavity Wire Connect to
A1 WHT Audio unit (AUD L-)
A2 RED Audio unit (AUD R-)
A3 GRN Audio unit (GA-NET ILL CTRL)
A4 GRN/RED Navigation display (CD EJECT)
A5 RED/BLU Audio unit (AUD BUS+(GA-NET))
A6 PUR Audio unit (SYSTEM ACC)
A7 YEL Audio unit (+B GA-NET)
A8 YEL Navigation display (NAVI SCTY2)
A9 GRN Audio unit (AUD L+)
A10 BLK Audio unit (AUD R+)
A11 LT GRN(1) Audio unit (AUD shield)
A12 GRN Navigation display (DISP OPEN)
A13 GRN/RED Audio unit (Ground)
A14 GRN/BLK(1) Audio unit (AUD BUS (GA-NET) shield)
A15 YEL Audio unit (AUD BUS- (GA-NET))
A16 GRN/BLK Audio unit (ILL+)
A17 BLU Audio unit (+B GA-NET2)
A18 RED/WHT MICU (SCTY IN)
B2 ORN(2) XM receiver (SAT SYSTEM ACC)
B3 LT GRN(3) Navigation display (AUDIO BUS (GA-NET) shield)
B4 GRY(2), (3) XM receiver (SAT shield)
B5 WHT(2) XM receiver (SAT R+)
B6 RED(2) XM receiver (SAT L+)
B9 WHT Navigation display (AUDIO BUS+ (GA-NET))
B10 BLU/RED Navigation display (AUDIO BUS- (GA-NET))
B13 BLK(2) XM receiver (SAT R-)
B14 GRN(2) XM receiver (SAT L-)
(1) The shielded wires have a heat-shrunk tube insulating the outside of the wire. The color of the insulating tube, typically black or dark gray, may not match the color of the wire listed on the schematic.
(2) With XM radio
(3) The shielded wires have a heat-shrunk tube insulating the outside of the wire. The color of the insulating tube, typically black or dark gray, may not match the color of the wire listed on the schematic.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.