Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHONDA2006S2000 L4-2.2LREPAIR AND DIAGNOSISENGINE, COOLING AND EXHAUSTENGINETUNE-UP AND ENGINE PERFORMANCE CHECKSIGNITION TIMINGTESTING AND INSPECTION
2006 Honda S2000 L4-2.2L
Ignition Timing: Testing and Inspection
2006 Honda S2000 L4-2.2LSECTION Testing and Inspection
Ignition Timing Inspection
1. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC), 2000-2005 models, 2006 model, and check for DTCs. If a DTC is present, diagnose and repair the cause before inspecting the ignition timing.
2. Turn the ignition switch ON (II).
3. 2006 model: Make sure the HDS communicates with the vehicle and the engine control module (ECM). If it doesn't, troubleshoot the DLC circuit.
4. Start the engine. Hold the engine speed at 3,000 rpm without load (in neutral) until the radiator fan comes on, then let it idle.
5. Check the idle speed:
- 2000-2005 models.
- 2006 model.
6. Jump the SCS line with the HDS.
7. Free the service loop (A) from the engine wire harness, then connect the timing light to the service loop.
8. Aim the light toward the pointer (A). Check the ignition timing under a no load condition (headlights, blower fan, and air conditioner are turned off).
9. If the ignition timing differs from the specification, check the cam timing. If the cam timing is OK, update the ECM if it does not have the latest software 2006 model, or substitute a known-good ECM, 2000-2005 models, 2006 model, then recheck. If the system works properly, and the ECM was substituted, replace the original ECM, 2000-2005 models, 2006 model.
10. Turn the ignition switch OFF.
11. Disconnect the HDS and the timing light.
12. Secure the service loop to the engine wire harness with wire ties.
1. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC), 2000-2005 models, 2006 model, and check for DTCs. If a DTC is present, diagnose and repair the cause before inspecting the ignition timing.
2. Turn the ignition switch ON (II).
3. 2006 model: Make sure the HDS communicates with the vehicle and the engine control module (ECM). If it doesn't, troubleshoot the DLC circuit.
4. Start the engine. Hold the engine speed at 3,000 rpm without load (in neutral) until the radiator fan comes on, then let it idle.
5. Check the idle speed:
- 2000-2005 models.
- 2006 model.
6. Jump the SCS line with the HDS.
7. Free the service loop (A) from the engine wire harness, then connect the timing light to the service loop.
8. Aim the light toward the pointer (A). Check the ignition timing under a no load condition (headlights, blower fan, and air conditioner are turned off).
9. If the ignition timing differs from the specification, check the cam timing. If the cam timing is OK, update the ECM if it does not have the latest software 2006 model, or substitute a known-good ECM, 2000-2005 models, 2006 model, then recheck. If the system works properly, and the ECM was substituted, replace the original ECM, 2000-2005 models, 2006 model.
10. Turn the ignition switch OFF.
11. Disconnect the HDS and the timing light.
12. Secure the service loop to the engine wire harness with wire ties.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.