Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBβ LIVE
HOMESERVICE MANUALSHONDA1993ACCORD L4-2156CC 2.2L SOHCREPAIR AND DIAGNOSISSPECIFICATIONSELECTRICAL SPECIFICATIONSPOWERTRAIN MANAGEMENTMANIFOLD PRESSURE/VACUUM SENSOR
1993 Honda Accord L4-2156cc 2.2L SOHC
Manifold Pressure/Vacuum Sensor
1993 Honda Accord L4-2156cc 2.2L SOHCSECTION Manifold Pressure/Vacuum Sensor
SENSOR SPECIFICATIONS:
BAROMETRIC PRESSURE (BARO) SENSOR
Atmospheric Pressure Output voltage chart
5 in. Hg. (125 mmHg.) 2.5 Volts
10 in. Hg. (250 mmHg.) 2.0 Volts
15 in. Hg. (375 mmHg. 1.5 Volts
20 in. Hg. (500 mmHg.) 1.0 Volts
25 in. Hg. (625 mmHg.) 0.5 Volts
ENGINE COOLANT TEMPERATURE (ECT) SENSOR
Coolant temperature resistance
-4° F (-20° C) 20K Ohms
32° F (0° C) 5K Ohms
104° F (40° C) 1K Ohms
176° F (80° C) 350 Ohms
248° F (120° C) 100 Ohms
INTAKE AIR TEMPERATURE (IAT) SENSOR
Intake Air temperature resistance
-4° F (-20° C) 20K Ohms
32° F (0° C) 5K Ohms
104° F (40° C) 1K Ohms
176° F (80° C) 350 Ohms
248° F (120° C) 100 Ohms
MANIFOLD ABSOLUTE PRESSURE SENSOR (MAP)
Manifold Absolute Pressure Output voltage chart
5 in. Hg. (125 mmHg.) 2.5 Volts
10 in. Hg. (250 mmHg.) 2.0 Volts
15 in. Hg. (375 mmHg.) 1.5 Volts
20 in. Hg. (500 mmHg.) 1.0 Volts
25 in. Hg. (625 mmHg.) 0.5 Volts
OXYGEN SENSOR
Mixture Output Voltage
Lean Less Than 0.4 Volts
14.7 to 1 Stoichiometric 0.4 - 0.6 Volts
Rich More Than 0.6 Volts
THROTTLE POSITION SENSOR
Throttle Position Output Voltage Chart
Throttle Closed (Idle) 0.2 Volts
14 Throttle 0.5 Volts
12 Throttle 2.0 Volts
34 Throttle 3.25 Volts
Full Throttle 4.5 Volts
FUEL INJECTOR
Connector Terminal Resistance 1.5 - 2.5 Ohms
FUEL INJECTOR RESISTOR
Terminals B, C, D, E, to A 5 - 7 Ohms
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.