Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSGENESIS2021GV80 2.5T ADVANCED, AWDREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTANTI-THEFT SYSTEMSINTEGRATED BODY CONTROL UNIT (IBU)COMPONENTS & COMPONENTS LOCATIONCOMPONENTSCONNECTOR PIN INFORMATION
2021 Genesis GV80 2.5T Advanced, AWD
Connector Pin Information
2021 Genesis GV80 2.5T Advanced, AWDSECTION Connector Pin Information
| No | Connector A | Connector B | Connector C | Connector B |
|---|---|---|---|---|
| 1 | - | - | ECU Ground | Driver capa sensor lock_input |
| 2 | - | - | Ground_power | - |
| 3 | - | ESCL (+)_output | Battery (+) ECU | - |
| 4 | PDW-R power_input | ESCL (-)_output | Battery (+) Power | - |
| 5 | - | - | Reserved3_output | - |
| 6 | - | - | Immobilizer antenna power_output | Start feedback_input |
| 7 | ACC relay_output | PDW switch indicator_output | Immobilizer antenna ground_output | Passenger capa sensor lock_input |
| 8 | - | - | IGN 1_Input | Passenger capa sensor unlock_input |
| 9 | ESCL COM | - | - | - |
| 10 | - | Reserved1_input | - | Wheel speed sensor_input |
| 11 | IGN1 relay_output | - | B_CAN (Low) | - |
| 12 | - | - | B_CAN (High) | - |
| 13 | IGN2 relay_output | - | Start relay_output | Front bumper antenna (+)_output |
| 14 | - | Reserved3_input | FD_CAN (Low) | Front bumper antenna power_output |
| 15 | - | - | FD_CAN (High) | Passenger outside handle antenna (+)_output |
| 16 | - | SSB switch 2_input | Body type (7P)_input | Driver outside handle antenna (+)_output |
| 17 | - | - | PDW-R switch_input | Trunk antenna (+)_output |
| 18 | - | - | IFU door unlock signal_output | Interior2 antenna power_output |
| 19 | Rear wiper relay | - | LIN3 | Interior1 antenna power_output |
| 20 | Security indicator | SSB symbol illumination (+)_output | LIN4 | ESCL Enable_output |
| 21 | PDW power_output | - | Reserved4_Print | RPM_input |
| 22 | - | - | - | - |
| 23 | - | - | ACC_Input | - |
| 24 | Brake switch_input | Reserved2_input | Reserved4_output | - |
| 25 | - | - | - | - |
| 26 | - | - | - | Driver capa sensor unlock_input |
| 27 | - | - | - | - |
| 28 | SSB symbol illumination (-)_output | Reserved4_input | Reserved2_output | - |
| 29 | - | - | kline IMMO | - |
| 30 | Puddle lamp_output | SSB switch1_input | - | Front bumper antenna (-)_output |
| 31 | - | ESCL unlock switch_input | P-position_input | Bumper antenna ground_output |
| 32 | - | - | - | Passenger outside handle antenna (-)_output |
| 33 | - | - | IGN2_input | Driver outside handle antenna (-)_output |
| 34 | - | LIN1 | Trunk antenna (-)_output | |
| 35 | - | LIN2 | Interior2 antenna ground_output | |
| 36 | - | - | Interior1 antenna ground_output | |
| 37 | External buzzer_output | |||
| 38 | PDW-R power_output |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.