K9 Body Control Module X6

2019 GMC Yukon XL Denali, RWDSECTION K9 Body Control Module X6
G00406218Courtesy of GENERAL MOTORS COMPANY
Connector Part Information
  • Harness Type: Body
  • OEM Connector: 13962300
  • Service Connector: 13587576
  • Description: 27-Way F 0.64, 2.8 Series (L-PU)
Terminal Part Information

Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575789 J-35616-35 (VT) J-38125-12A SNAC-A061T-M2.8 Delphi 20 C A
II 13582297 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
III Not Required J-35616-64B (LT BU) No Tool Required Not Available Not Available Not Available Not Available
Pin Size Color Circuit Function Terminal Type ID Option
1 1.5 BU/WH 195 Door Lock Control I -
2 1.5 GY/GN 3271 Door Lock Control 2 I -
3 1.5 BK 1850 Ground I -
4 1.5 BN/YE 294 Door Lock Actuator Unlock Control I -
5 0.35 VT/GY 1303 Lift Gate Ajar Switch Signal 1 II -
6 0.5 WH/BU 3203 Right Headlamp Bulb Outage Signal II -
7 0.5 YE/WH 58 Right Cornering Lamp Control II -
8 0.35 VT/WH 5908 Passenger Seat Vent Motor Control 1 II -
9 0.5 GN/BU 6133 Local Interconnect Network Serial Data Bus 2 II -
10 0.5 GN/YE 6134 Local Interconnect Network Serial Data Bus 3 II -
11 - - - Not Occupied - -
12 0.5 YE/BK 5356 Left Tail Lamp Outage Detection Signal II -
13 0.5 VT/BU 7598 Glass Breakage Sensor Signal 2 III -
14 - - - Not Occupied - -
15 0.35 GY/GN 6190 Lift Glass/Rear Compartment Lid Exterior Release Signal II -
16 0.5 GN/BN 6132 Local Interconnect Network Serial Data Bus 1 II -
17 0.35 GN/VT 5906 Driver Seat Vent Motor Control 1 II -
18 - 20 - - - Not Occupied - -
21 0.5 BU/VT 3204 Left Headlamp Bulb Outage Signal II -
22 0.5 VT/YE 5357 Right Tail Lamp Outage Detection Signal II -
23 - - - Not Occupied - -
24 0.5 BU 2500 High Speed GMLAN Serial Data (+) 1 II -
25 0.5 WH 2501 High Speed GMLAN Serial Data (-) 1 II -
26 - - - Not Occupied - -
27 0.35 WH/VT 2092 Fuel Saver Mode (ECO) Switch Signal II -
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.