Circuit/System Testing

1. Attempt to communicate with all control modules on the low speed GMLAN serial data circuit. Refer to Data Link References . Communications should not be available with two or more control modules on the low speed GMLAN serial data circuit.
   • If only one control module is not communicating, diagnose that control module only. Refer to DTC U0100-U02FF (except U029D and U029E) , DTC U0100-U02FF (U029D and U029E only) .
   • If one or more control modules are communicating but not all, refer to Testing the Serial Data Circuit for an Open/High Resistance below.
2. Disconnect the scan tool from the DLC. The following tests will be done at the DLC connector.
3. All access doors closed, ignition OFF for 60 seconds, test for less than 10 Ω between the ground circuit terminal 5 and ground.
   • If greater than the specified range, test the ground circuit for an open/high resistance.
4. Ignition ON, test for less than 4.5 V between the serial data circuit terminal 1 and ground.
   • If greater than the specified range, test the serial data circuit for a short to voltage. Refer to Testing the Serial Data Circuit for a Short to Voltage below.
5. Ignition OFF for 60 seconds, test for greater than 100 Ω between the serial data circuit terminal 1 and ground.
   • If less than the specified range, test the serial data circuit for a short to ground. Refer to Testing the Serial Data Circuits for a Short to ground below.
6. Disconnect the appropriate harness connector at the JX 200 splice pack.
7. Test for less than 2 Ω between the DLC serial data circuit terminal 1 and the JX200 splice pack terminal 1.
   • If greater than the specified range, test the serial data circuit for an open/high resistance. If the circuits test normal, replace the splice pack.

Testing the Serial Data Circuits for a Short to Voltage

1. Ignition OFF, disconnect the appropriate harness connectors at the JX 200 splice pack.
2. Ignition ON, test for less than 4.5 V between the DLC serial data circuit terminal 1 and ground.
   • If greater than the specified range, repair the short to voltage.
3. Test for less than 4.5 V between each serial data circuit at the splice pack connector and ground.
   • If greater than the specified range, perform the appropriate test listed below:
   • Serial data circuits with one control module, test the serial data circuit for a short to voltage. If the circuit tests normal replace the control module.
   • Serial data circuits with 2 or more control modules, test each section of the serial data circuit for a short to voltage. If the circuits test normal, replace the control module that causes the short to voltage when connected.

Testing the Serial Data Circuits for a Short to Ground

1. Ignition OFF, disconnect the appropriate harness connectors at the JX 200 splice pack.
2. Test for infinite resistance between the DLC serial data circuit terminal 1 and ground.
   • If not the specified value, repair the short to ground.
3. Ignition OFF for 60 seconds, test for greater than 100 Ω between each serial data circuit at the splice pack and ground.
   • If less than the specified range, perform the appropriate test listed below:
   • Serial data circuits with one control module, test the serial data circuit for a short to ground. If the circuit tests normal replace the control module.
   • Serial data circuits with 2 or more control modules, test each section of the serial data circuit for a short to voltage. If the circuits test normal, replace the control module that causes the short to ground when connected.

Testing the Serial Data Circuit for an Open/High Resistance

1. Ignition OFF, disconnect the appropriate harness connectors at the JX 200 splice pack.
2. Install a 3 A fused jumper wire between the disconnected splice pack connector terminal 1 and a low speed GMLAN serial data circuit terminal that is not communicating.
3. Ignition ON, verify the scan tool communicates with the control modules connected to the low speed GMLAN serial data circuit.
   • If any control module does not communicate, test each section of the serial data circuit for an open/high resistance. If the circuits test normal, replace the control module that does not communicate when connected.
4. If all circuits test normal, replace the splice pack.