SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSGMC2011YUKON BASE, 5.3 0, RWDREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSWIRING DIAGRAMSWIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - ELECTRONIC STEERING CONTROL MODULE X2 THROUGH MEMORY SEAT MODULECOMPONENT CONNECTOR END VIEWSENGINE CONTROL MODULE (ECM) X1 (HP2)
2011 GMC Yukon Base, 5.3 0, RWD

Engine Control Module (ECM) X1 (HP2)

2011 GMC Yukon Base, 5.3 0, RWDSECTION Engine Control Module (ECM) X1 (HP2)
Fig 1: Engine Control Module (ECM) X1 (HP2) Connector End View
GM784851Courtesy of GENERAL MOTORS CORP.
Engine Control Module (ECM) X1 (HP2)

Pin Wire Circuit Function
1-2 - - Not Used
3 0.5 PU 5531 Hood Switch Signal
4-6 - - Not Used
7 0.5 L-BU/WH 6311 Brake Pedal Switch Signal
8 0.5 PK/BK 109 Hood Ajar Switch Signal
9 0.35 TN/BK 6049 Low Reference
10-11 - - Not Used
12 0.35 BN/WH 419 Malfunction Indicator Lamp (MIL) Control
13 0.35 D-GN/WH 465 Fuel Pump Control Module Enable
14-17 - - Not Used
18 0.5 D-BU 5985 Serial Data Wake-Up Signal
19 0.5 PK 439 Ignition Voltage
20 0.5 RD/WH 440 Battery Positive Voltage
21-32 - - Not Used
33 0.35 WH/BK 1164 5-Volt Reference 2
34 0.35 GY 2709 5-Volt Reference 1
35 0.35 TN 1274 5-Volt Reference 1
36 0.35 BN 1271 Low Reference
37 0.35 PU 1272 Low Reference
38-39 - - Not Used
40 0.35 YE 5991 Powertrain Relay Coil Control
41 0.35 PU 5128 High Speed Cooling Fan Relay Control
42-43 - - Not Used
44 0.35 PU 1589 Fuel Level Sensor Signal
45-46 - - Not Used
47 0.35 D-BU 1161 Accelerator Pedal Position Sensor 1 Signal
48 0.35 D-GN 890 Fuel Tank Pressure Sensor Signal
49 0.35 L-BU 1162 Accelerator Pedal Position Sensor 2 Signal
50-53 - - Not Used
54 0.35 D-GN 335 Medium Speed Cooling Fan Relay Control
55 0.5 WH 1310 EVAP Canister Vent Solenoid Control
56 - - Not Used
Connector Part Information
  • Harness Type: Engine
  • OEM Connector: 13510837
  • Service Connector: 88988373
  • Description: 56-Way F MX123 Series Sealed (BU Encased in BK)
Terminal Part Information
  • Pins: 3, 7, 8, 18-20, 55
  • Terminated Lead: 13575575
  • Release Tool: J-38125-213
  • Diagnostic Test Probe: J-35616-64B (L-BU)
  • Terminal/Tray: 33467-0005/23
  • Core/Insulation Crimp: J/J
  • Pins: 9, 12, 13, 33-37, 40, 41, 44, 47-49, 54
  • Terminated Lead: 13575811
  • Release Tool: J-38125-213
  • Diagnostic Test Probe: J-35616-64B (L-BU)
  • Terminal/Tray: 33467-0003/23
  • Core/Insulation Crimp: H/H
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.