Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSGMC2011SAVANA SPECIAL 4.8 AREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 40 (DISC BRAKE SYSTEM)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2011 GMC Savana Special 4.8 A
Fastener Tightening Specifications
2011 GMC Savana Special 4.8 ASECTION Fastener Tightening Specifications
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2010 GMC Savana Special, 2010 GMC Savana Camper Special, 2010 GMC Savana, 2010 Chevrolet RV Cutaway, and 2010 Chevrolet Cutaway. However, it is still accessible from the selected car via links, so may be relevant.
| Application | Specification | |
|---|---|---|
| Metric | English | |
| All | ||
| Brake Caliper Bleeder Screw | 12 N.m | 106 lb in |
| Front Brakes - JH5 | ||
| Brake Caliper Bracket Bolt | 175 N.m | 129 lb ft |
| Brake Caliper Guide Pin Bolt | 100 N.m | 74 lb ft |
| Brake Hose Fitting Bolt | 44 N.m | 32 lb ft |
| Brake Rotor Retaining Screw | 12 N.m | 106 lb in |
| Front Brakes - JH6, JH9 | ||
| Brake Caliper Bracket Bolt | 300 N.m | 221 lb ft |
| Brake Caliper Guide Pin Bolt | 108 N.m | 80 lb ft |
| Brake Hose Fitting Bolt | 44 N.m | 32 lb ft |
| Front Hub Extension Nut (JH9) | 130 N.m | 96 lb ft |
| Rear Brakes - JH5, JH6 | ||
| Brake Caliper Bracket Bolt | 200 N.m | 148 lb ft |
| Brake Caliper Guide Pin Bolt (JH5) | 34 N.m | 25 lb ft |
| Brake Caliper Guide Pin Bolt (JH6) | 72 N.m | 53 lb ft |
| Brake Hose Fitting Bolt | 44 N.m | 32 lb ft |
| Brake Shield Nut | 135 N.m | 100 lb ft |
| Rear Brakes - JH9 | ||
| Brake Caliper Bracket Bolt | 300 N.m | 221 lb ft |
| Brake Caliper Guide Pin Bolt | 61 N.m | 45 lb ft |
| Brake Hose Fitting Bolt | 40 N.m | 30 lb ft |
| Brake Shield Bolt | 10 N.m | 89 lb in |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.