SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSGMC2011SAVANA SPECIAL 4.8 AREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 40 (DISC BRAKE SYSTEM)SPECIFICATIONSDISC BRAKE COMPONENT SPECIFICATIONS
2011 GMC Savana Special 4.8 A

Disc Brake Component Specifications

2011 GMC Savana Special 4.8 ASECTION Disc Brake Component Specifications
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2010 GMC Savana Special, 2010 GMC Savana Camper Special, 2010 GMC Savana, 2010 Chevrolet RV Cutaway, and 2010 Chevrolet Cutaway. However, it is still accessible from the selected car via links, so may be relevant.
Application Specification
Metric English
Front Brake JH5
  • Rotor Discard Thickness *
 27.50 mm 1.083 in
  • Rotor Minimum Allowable Thickness After Refinish
 28.0 mm 1.102 in
  • Rotor Thickness New
 29.0 mm 1.142 in
  • Rotor Maximum Allowable Lateral Runout
 0.13 mm 0.005 in
  • Rotor Maximum Allowable Scoring
 1.50 mm 0.059 in
  • Rotor Maximum Allowable Thickness Variation
 0.025 mm 0.001 in
Front Brake JH6
  • Rotor Discard Thickness *
 36.50 mm 1.437 in
  • Rotor Minimum Allowable Thickness After Refinish
 37.0 mm 1.457 in
  • Rotor Thickness New
 38.0 mm 1.496 in
  • Rotor Maximum Allowable Lateral Runout
 0.13 mm 0.005 in
  • Rotor Maximum Allowable Scoring
 1.50 mm 0.059 in
  • Rotor Maximum Allowable Thickness Variation
 0.025 mm 0.001 in
Front Brake JH9
  • Rotor Discard Thickness *
 36.50 mm 1.437 in
  • Rotor Minimum Allowable Thickness After Refinish
 37.0 mm 1.457 in
  • Rotor Thickness New
 38.0 mm 1.496 in
  • Rotor Maximum Allowable Lateral Runout
 0.13 mm 0.005 in
  • Rotor Maximum Allowable Scoring
 1.50 mm 0.059 in
  • Rotor Maximum Allowable Thickness Variation
 0.025 mm 0.001 in
Rear Brake JH5
  • Rotor Discard Thickness *
 28.50 mm 1.122 in
  • Rotor Minimum Allowable Thickness After Refinish
 29.0 mm 1.142 in
  • Rotor Thickness New
 30.0 mm 1.181 in
  • Rotor Maximum Allowable Lateral Runout
 0.13 mm 0.005 in
  • Rotor Maximum Allowable Scoring
 1.50 mm 0.059 in
  • Rotor Maximum Allowable Thickness Variation
 0.025 mm 0.001 in
Rear Brake JH6
  • Rotor Discard Thickness *
 27.50 mm 1.083 in
  • Rotor Minimum Allowable Thickness After Refinish
 28.0 mm 1.102 in
  • Rotor Thickness New
 29.0 mm 1.142 in
  • Rotor Maximum Allowable Lateral Runout
 0.13 mm 0.005 in
  • Rotor Maximum Allowable Scoring
 1.50 mm 0.059 in
  • Rotor Maximum Allowable Thickness Variation
 0.025 mm 0.001 in
Rear Brake JH9
  • Rotor Discard Thickness *
 38.5 mm 1.516 in
  • Rotor Minimum Allowable Thickness After Refinish
 39.0 mm 1.535 in
  • Rotor Thickness New
 40.0 mm 1.575 in
  • Rotor Maximum Allowable Lateral Runout
 0.13 mm 0.005 in
  • Rotor Maximum Allowable Scoring
 1.50 mm 0.059 in
  • Rotor Maximum Allowable Thickness Variation
 0.025 mm 0.001 in
* All brake rotors have a discard dimension cast into them. Replace any rotor that does not meet this specification. After refinishing the rotor, replace any rotor that does not meet the minimum thickness specifications.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.