SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSGMC2011SAVANA SPECIAL 4.8 AREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 203 (WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - 1-2 SHIFT SOLENOID THROUGH FUEL INJECTOR 5)COMPONENT CONNECTOR END VIEWSBODY CONTROL MODULE (BCM)BODY CONTROL MODULE (BCM) X4
2011 GMC Savana Special 4.8 A

Body Control Module (BCM) X4

2011 GMC Savana Special 4.8 ASECTION Body Control Module (BCM) X4
WARNING: This page is about a different car, the 2011 GMC Savana, 2011 Chevrolet RV Cutaway, 2011 Chevrolet Cutaway, and 2011 Chevrolet Chevy Express. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Connector End View Body Control Module (BCM) X4
GM1664499Courtesy of GENERAL MOTORS CORP.
Body Control Module (BCM) X4

Pin Wire Circuit Function
1 0.8 RD/WH 2740 Battery Positive Voltage
2 0.8 RD/WH 3040 Battery Positive Voltage
3 0.8 RD/WH 2940 Battery Positive Voltage
4 0.8 RD/WH 2240 Battery Positive Voltage
5 0.8 D-BU/WH 1315 Right Front Turn Signal Lamp Control
6 0.35 D-GN 6134 Local Interconnect Network 3
7 0.35 YE 196 Windshield Wiper Motor Park Switch Signal
8 - - Not Used
9 0.5 BK/WH 451 Ground (LU3 or LMF)
10 0.5 RD/WH 2840 Battery Positive Voltage (LU3 or LMF)
11 0.5 L-GN 1391 Ignition Voltage (PRP)
12 0.35 YE 5187 Right Trailer Turn Signal Lamp (UY7)
13 0.35 OG 5186 Left Trailer Turn Signal Lamp (UY7)
14 - - Not Used
15 0.35 OG 2268 Windshield Washer Relay Control
16 0.35 TN/WH 1969 Headlamp High Beam Relay Control
17-18 - - Not Used
19 0.5 D-BU 5985 Accessory Wakeup Serial Data
20 0.5 L-BU 1344 Trunk Release Control (PRP)
21 0.35 YE 5199 Run/Crank Relay Coil Control
22 - - Not Used
23 0.35 PU 544 Headlamp Low Beam Control
24 0.5 L-BU 244 Front Passenger Door Lock Switch Lock Control (PRP)
25 - - Not Used
Connector Part Information
  • Harness Type: Instrument Panel
  • OEM Connector: 15482792
  • Service Connector: 88988841
  • Description: 25-Way F HIT Series (BK)
Terminal Part Information
  • Pins: 1-5
  • Terminated Lead: 13327199
  • Release Tool: J-38125-12A
  • Diagnostic Test Probe: J-35616-35 (VT)
  • Terminal/Tray: SNAC-A061T-M2.8/20
  • Core/Insulation Crimp: E/A
  • Pins: 6-7, 9-13, 15-17, 19-21, 23-24
  • Terminated Lead: 13575870
  • Release Tool: J-38125-12A
  • Diagnostic Test Probe: J-35616-64B (L-BU)
  • Terminal/Tray: SNAC3-A021T-M0.64/20
  • Core/Insulation Crimp: J/J
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.