Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSGMC2004ENVOY 2WD L6-4.2L VIN SREPAIR AND DIAGNOSISLIGHTING AND HORNSDOME LAMPDOME LAMP BULBSERVICE AND REPAIR
2004 GMC Envoy 2WD L6-4.2L VIN S
Dome Lamp Bulb: Service and Repair
2004 GMC Envoy 2WD L6-4.2L VIN SSECTION Service and Repair
DOME AND READING LAMP BULB REPLACEMENT
REMOVAL PROCEDURE
1. Carefully grasp the sides of the lens to partially expose the rear retaining tab.
2. Use a flat bladed tool in order to release the rear lens retaining tab.
3. Lower the rear edge of the lens away from the headliner.
4. Move the lens rearward in order to release the front horizontal retaining tab.
5. Remove the lens from the headliner.
6. If replacing the reading lamp bulb (1), remove the reflector (2) from the dome lamp.
7. Remove the reading lamp bulb from the socket.
8. If replacing the dome lamp bulb (1), remove the dome lamp bulb from the socket.
INSTALLATION PROCEDURE
1. If replacing the dome lamp bulb (1), install the dome lamp bulb to the socket.
2. If replacing the reading lamp bulb (1), install the reading lamp bulb to the socket.
3. Install the reflector (2) to the dome lamp, ensuring the retaining tabs are fully seated.
4. Position the lens to the headliner with the horizontal tab facing forward.
5. Position the horizontal tab above the headliner and push the lens forward to seat the tab.
6. Push upward on the rear portion of the lens, in order to seat the rear lens retaining tab.
7. Pull down on the lens to ensure that the lens is secured to the headliner.
REMOVAL PROCEDURE
1. Carefully grasp the sides of the lens to partially expose the rear retaining tab.
2. Use a flat bladed tool in order to release the rear lens retaining tab.
3. Lower the rear edge of the lens away from the headliner.
4. Move the lens rearward in order to release the front horizontal retaining tab.
5. Remove the lens from the headliner.
6. If replacing the reading lamp bulb (1), remove the reflector (2) from the dome lamp.
7. Remove the reading lamp bulb from the socket.
8. If replacing the dome lamp bulb (1), remove the dome lamp bulb from the socket.
INSTALLATION PROCEDURE
1. If replacing the dome lamp bulb (1), install the dome lamp bulb to the socket.
2. If replacing the reading lamp bulb (1), install the reading lamp bulb to the socket.
3. Install the reflector (2) to the dome lamp, ensuring the retaining tabs are fully seated.
4. Position the lens to the headliner with the horizontal tab facing forward.
5. Position the horizontal tab above the headliner and push the lens forward to seat the tab.
6. Push upward on the rear portion of the lens, in order to seat the rear lens retaining tab.
7. Pull down on the lens to ensure that the lens is secured to the headliner.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.