Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSGMC1999FORWARD CONTROL 5.7 R, AUTOMATICREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 78 (ENGINE CONTROL SYSTEM SELF-DIAGNOSTICS - 3.8L)DIAGNOSTIC TESTSDTC P0201-P0206: INJECTOR CONTROL CIRCUITDIAGNOSTIC PROCEDURES
1999 GMC Forward Control 5.7 R, Automatic
Diagnostic Procedures
1999 GMC Forward Control 5.7 R, AutomaticSECTION Diagnostic Procedures
WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2002 Pontiac Grand Prix, 2002 Pontiac Bonneville, 2002 Chevrolet Monte Carlo, 2002 Chevrolet Impala, and 2002 Buick Regal. However, it is still accessible from the selected car via links, so may be relevant.
- Perform Diagnostic System Check - Engine Controls. See DIAGNOSTIC SYSTEM CHECK - ENGINE CONTROLS under SELF-DIAGNOSTIC SYSTEM. After performing Diagnostic System Check - Engine Controls, go to next step.
- Using scan tool, clear DTCs. Idle engine at normal operating temperature. Using scan tool, monitor misfire current counters. Are any of the misfire current counters incrementing? If yes, go to step 4. If no, go to next step.
- Observe FREEZE FRAME/FAILURE RECORDS data for this DTC. Turn ignition off for 30 seconds. Start engine. Operate vehicle within Conditions for Running DTC or as close to FREEZE FRAME/FAILURE RECORDS data as possible. Does the DTC fail this ignition cycle? If yes, go to next step. If no, see DIAGNOSTIC AIDS .
- Turn ignition off. Disconnect appropriate harness connector of fuel injector. Turn ignition on, engine off. Using test light connected to ground, probe fuel injector connector terminal "A" (Pink wire). Does the test lamp illuminate? If yes, go to next step. If no, go to step 11.
- Connect Injector Test Lamp (J 34730-405 or J 34730-2C) between fuel injector connector terminals. Start engine. Does the test lamp blink? If yes, go to step 9. If no, go to next step.
- Does the test lamp remain illuminated at all times? If yes, go to step 8. If no, go to next step.
- Check control circuit of affected fuel injector for short to voltage or open. Did you find and correct the condition? If yes, go to step 14. If no, go to step 10.
- Check control circuit of affected fuel injector for short to ground. Did you find and correct the condition? If yes, go to step 14. If no, go to step 13.
- Check fuel injector connector for poor connections. Did you find and correct the condition? If yes, go to step 14. If no, go to step 12.
- Check PCM connectors for poor connections. Did you find and correct the condition? If yes, go to step 14. If no, go to step 13.
- Repair the ignition voltage circuit of the fuel injector for an open or a short to ground. After repairs, go to step 14.
- Replace fuel injector. After repairs, go to step 14.
- Replace PCM. Program replacement PCM. See POWERTRAIN CONTROL MODULE under PROGRAMMING. After repairs, go to next step.
- Using scan tool, clear DTCs. Turn ignition off for 30 seconds. Start engine. Operate vehicle within Conditions for Running DTC. Does DTC run and pass? If yes, go to next step. If no, go to step 2.
- Using scan tool, observe stored information. Does scan tool displays any DTCs that have not been diagnosed? If yes, see DIAGNOSTIC TROUBLE CODE DEFINITIONS . If no, system is okay.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.