Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBβ LIVE
HOMESERVICE MANUALSGMC1999FORWARD CONTROL 5.7 R, AUTOMATICREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 729 (ENGINE CONTROLS (INTRODUCTION) -- 5.7L)COMPONENT LOCATORENGINE CONTROLS CONNECTOR END VIEWS
1999 GMC Forward Control 5.7 R, Automatic
Engine Controls Connector End Views
1999 GMC Forward Control 5.7 R, AutomaticSECTION Engine Controls Connector End Views
WARNING: This page is about a different car, the 2004 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
Accelerator Pedal Position Terminal Identification (APP) Sensor
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | GRY | 1273 | Low Reference |
| B | PPL | 1272 | Low Reference |
| C | LT BLU | 1162 | APP Sensor 2 Signal |
| D | TAN | 1274 | 5-Volt Reference |
| E | YEL/BLK | 1275 | 5-Volt Reference |
| F | DK BLU | 1161 | APP Sensor 1 Signal |
| G | LT BLU | 1276 | 5-Volt Reference |
| H | - | - | Not Used |
| J | BRN | 1271 | Low Reference |
| K | DK GRN | 1163 | APP Sensor 3 Signal |
Camshaft Position Terminal Identification (CMP) Sensor
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BRN/WHT | 633 | CMP Sensor Signal |
| B | PNK/BLK | 632 | Low Reference |
| C | RED | 631 | 12-Volt Reference |
Crankshaft Position Terminal Identification (CKP) Sensor
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | DK BLU/WHT | 1869 | CKP Sensor Signal |
| B | YEL/BLK | 1868 | Low Reference |
| C | LT GRN | 1867 | 12-Volt Reference |
Engine Coolant Temperature Terminal Identification (ECT) Sensor
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BRN | 718 | Low Reference |
| B | YEL | 410 | ECT Sensor Signal |
Evaporative Emission (EVAP) Canister Purge Solenoid Terminal Identification
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 339 | Ignition (Hot W/IGN Relay Energized) |
| B | DK GRN/WHT | 428 | EVAP Canister Purge Solenoid Control |
Evaporative Emission (EVAP) Canister Vent Solenoid Terminal Identification
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 339 | Battery Positive Feed |
| B | WHT | 1310 | EVAP Canister Vent Solenoid Control |
Fuel Injector Terminal Identification 1
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 639 | Ignition 1 Voltage |
| B | BLK | 1744 | Fuel Injector #1 Control |
Fuel Injector Terminal Identification 2
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 839 | Ignition 1 Voltage |
| B | LT GRN/BLK | 1745 | Fuel Injector #2 Control |
Fuel Injector Terminal Identification 3
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 639 | Ignition 1 Voltage |
| B | PNK/BLK | 1746 | Fuel Injector #3 Control |
Fuel Injector Terminal Identification 4
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 839 | Ignition 1 Voltage |
| B | LT BLU/BLK | 844 | Fuel Injector #4 Control |
Fuel Injector Terminal Identification 5
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 639 | Ignition 1 Voltage |
| B | BLK/WHT | 845 | Fuel Injector #5 Control |
Fuel Injector Terminal Identification 6
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 839 | Ignition 1 Voltage |
| B | YEL/BLK | 846 | Fuel Injector #6 Control |
Fuel Injector Terminal Identification 7
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 639 | Ignition 1 Voltage |
| B | RED/BLK | 877 | Fuel Injector #7 Control |
Fuel Injector Terminal Identification 8
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 839 | Ignition 1 Voltage |
| B | DK BLU/WHT | 878 | Fuel Injector #8 Control |
Fuel Pump And Sender Assembly Terminal Identification
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | DK BLU | 1936 | Fuel Level Sensor Signal - Secondary |
| 2 | GRY | 120 | Fuel Pump Supply Voltage |
| 3 | BLK | 9531 | Ground |
| 4 | BLK | 808 | Low Reference |
Fuel Tank Pressure Terminal Identification (FTP) Sensor
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BLK | 808 | Low Reference |
| B | DK GRN | 890 | Fuel Tank Pressure Sensor Signal |
| C | BRN/ LT GRN | 2709 | 5-Volt Reference Voltage |
Heated Oxygen Sensor Terminal Identification (HO2S) Bank 1 Sensor 1
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | TAN/WHT | 1653 | HO2S Low Signal Bank 1 Sensor 1 |
| B | PPL/WHT | 1665 | HO2S High Signal Bank 1 Sensor 1 |
| C | BLK/WHT | 3113 | HO2S Heater Low Control |
| D | BRN | 241 | Ignition 3 Voltage |
Heated Oxygen Sensor Terminal Identification (HO2S) Bank 1 Sensor 2
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | TAN/WHT | 1669 | HO2S Low Signal Bank 1 Sensor 2 |
| B | PPL/WHT | 1668 | HO2S High Signal Bank 1 Sensor 2 |
| C | BRN | 2391 | HO2S Heater Low Control |
| D | BRN | 241 | Ignition 3 Voltage |
Heated Oxygen Sensor Terminal Identification (HO2S) Bank 2 Sensor 1
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | TAN | 1667 | HO2S Low Signal Bank 2 Sensor 1 |
| B | PPL | 1666 | HO2S High Signal Bank 2 Sensor 1 |
| C | LT GRN | 3212 | HO2S Heater Low Control |
| D | BRN | 241 | Ignition 3 Voltage |
Heated Oxygen Sensor Terminal Identification (HO2S) Bank 2 Sensor 2
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | TAN | 1671 | HO2S Low Signal Bank 2 Sensor 2 |
| B | PPL | 1670 | HO2S High Signal Bank 2 Sensor 2 |
| C | RED/WHT | 3223 | HO2S Heater Low Control |
| D | BRN | 241 | Ignition 3 Voltage |
Ignition Coil/Module Terminal Identification 1
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BLK | 151 | Ground |
| B | BRN | 2129 | Low Reference |
| C | PPL | 2121 | IC 1 Control |
| D | PNK | 39 | Ignition 1 Voltage |
Ignition Coil/Module Terminal Identification 2
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BLK | 151 | Ground |
| B | BRN | 2129 | Low Reference |
| C | RED | 2127 | IC 2 Control |
| D | PNK | 39 | Ignition 1 Voltage |
Ignition Coil/Module Terminal Identification 3
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BLK | 151 | Ground |
| B | BRN | 2129 | Low Reference |
| C | LT BLU | 2123 | IC 3 Control |
| D | PNK | 39 | Ignition 1 Voltage |
Ignition Coil/Module Terminal Identification 4
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BLK | 151 | Ground |
| B | BRN | 2129 | Low Reference |
| C | DK GRN | 2125 | IC 4 Control |
| D | PNK | 39 | Ignition 1 Voltage |
Ignition Coil/Module Terminal Identification 5
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BLK | 151 | Ground |
| B | BRN | 2129 | Low Reference |
| C | DK GRN | 2125 | IC 5 Control |
| D | PNK | 39 | Ignition 1 Voltage |
Ignition Coil/Module Terminal Identification 6
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BLK | 151 | Ground |
| B | BRN | 2129 | Low Reference |
| C | LT BLU | 2123 | IC 6 Control |
| D | PNK | 39 | Ignition 1 Voltage |
Ignition Coil/Module Terminal Identification 7
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BLK | 151 | Ground |
| B | BRN | 2129 | Low Reference |
| C | RED | 2127 | IC 7 Control |
| D | PNK | 39 | Ignition 1 Voltage |
Ignition Coil/Module Terminal Identification 8
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BLK | 151 | Ground |
| B | BRN | 2129 | Low Reference |
| C | PPL | 2121 | IC 8 Control |
| D | PNK | 39 | Ignition 1 Voltage |
Knock Sensor Terminal Identification (KS) 1
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | DK BLU | 496 | KS 1 Signal |
Knock Sensor Terminal Identification (KS) 2
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | LT BLU | 1876 | KS 2 Signal |
Manifold Absolute Pressure Terminal Identification (MAP) Sensor
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | ORN/BLK | 469 | Low Reference |
| B | LT GRN | 432 | MAP Sensor Signal |
| C | GRY | 416 | 5-Volt Reference |
Mass Air Flow Terminal Identification (MAF) Sensor
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PPL | 719 | Low Reference |
| B | TAN | 472 | IAT Sensor Signal |
| C | BLK/WHT | 451 | Ground |
| D | PNK | 339 | Ignition 1 Voltage |
| E | YEL | 492 | Mass Air Flow (MAF) Sensor - Signal |
Park/Neutral Position (PNP) Switch Terminal Identification - C1
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | - | - | Not Used |
| B | ORN/BLK | 434 | Neutral Safety Switch Signal |
| C | BRN | 341 | Ignition 3 Voltage |
| D | BLK/WHT | 851 | Ground |
| E | PPL | 1606 | Crank Voltage |
| F | GRY | 1524 | Back Up Lamp Supply Voltage |
| G | YEL | 269 | Starter Enable Relay Coil Supply Voltage |
Park/Neutral Position (PNP) Switch Terminal Identification - C2
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BLK/WHT | 771 | Transmission Range Switch Signal A |
| B | GRY | 773 | Transmission Range Switch Signal C |
| C | WHT | 776 | Transmission Range Switch Signal P |
| D | YEL | 772 | Transmission Range Switch Signal B |
Secondary Air Injection (AIR) Pump Terminal Identification
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | RED | 78 | AIR Pump Supply Voltage |
| B | BLK | 150 | Ground |
Secondary Air Injection (AIR) Solenoid Terminal Identification
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 339 | Ignition 1 Voltage |
| B | PPL | 421 | Air Solenoid Control |
Throttle Actuator Control (TAC) Module Terminal Identification C1
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | GRY | 1273 | Low Reference |
| B | PPL | 1272 | Low Reference |
| C | LT BLU | 1162 | APP Sensor 2 Signal |
| D | TAN | 1274 | 5-Volt Reference |
| E | YEL/BLK | 1275 | 5-Volt Reference |
| F | DK BLU | 1161 | APP Sensor 1 Signal |
| G | LT BLU | 1276 | 5-Volt Reference |
| H | - | - | Not Used |
| J | BRN | 1271 | Low Reference |
| K | DK GRN | 1163 | APP Sensor 3 Signal |
Throttle Actuator Control (TAC) Module Terminal Identification C2
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | DK BLU | 417 | TP Sensor 1 Signal |
| 2 | DK GRN | 485 | 5-Volt Reference |
| 3 | PPL | 486 | Low Reference |
| 4 | DK BLU | 84 | Cruise Control Set/Coast Switch Signal |
| 5 | GRY/BLK | 87 | Cruise Control Resume/Accel Switch Signal |
| 6 | LT BLU | 20 | Stop Lamp Supply Voltage |
| 7 | PNK | 539 | Ignition 1 Voltage |
| 8 | BRN | 582 | TAC Motor Control - 2 |
| 9 | YEL/BLK | 487 | 5-Volt Reference |
| 10 | WHT | 484 | Low Reference |
| 11 | PNK | 427 | TP Sensor 2 Signal |
| 12 | TAN | 800 | UART Serial Data Primary |
| 13 | ORN/BLK | 1061 | UART Serial Data Secondary |
| 14 | GRY | 397 | Cruise Control On Signal |
| 15 | BLK/WHT | 451 | Ground |
| 16 | YEL | 581 | TAC Motor Control - 1 |
Throttle Actuator Control (TAC) Motor Terminal Identification
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | YEL | 581 | TAC Motor Control - 1 |
| B | BRN | 582 | TAC Motor Control - 2 |
Throttle Position Terminal Identification (TP) Sensor
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | DK GRN | 485 | 5-Volt Reference |
| B | PPL | 486 | Low Reference |
| C | DK BLU | 417 | TP Sensor 1 Signal |
| D | YEL/BLK | 487 | 5-Volt Reference |
| E | WHT | 484 | Low Reference |
| F | PNK | 427 | TP Sensor 2 Signal |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.