Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2021TRANSIT-350 HD BASE, VAN CARGO EXTENDED, 3.5L ENG VIN 8, AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 171 (STEERING WHEEL AND COLUMN ELECTRICAL COMPONENTS)GENERAL PROCEDURESSTEERING COLUMN MULTIFUNCTION SWITCH ADJUSTMENT
2021 Ford Transit-350 HD Base, Van Cargo Extended, 3.5L Eng VIN 8, AWD
Steering Column Multifunction Switch Adjustment
2021 Ford Transit-350 HD Base, Van Cargo Extended, 3.5L Eng VIN 8, AWDSECTION Steering Column Multifunction Switch Adjustment
WARNING: This page is about a different car, the 2019 Ford F-550 Super Duty, 2019 Ford F-450 Super Duty, 2019 Ford F-350 Super Duty, and 2019 Ford F-250 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.
For information on Ford Color Coded Illustrations refer to OEM Color Coding
Adjustment
- Using a diagnostic scan tool, retrieve and diagnose all SECM Diagnostic Trouble Codes (DTCs). Refer to: Adaptive Steering .
- Using a diagnostic scan tool, retrieve and diagnose all SASM Diagnostic Trouble Codes (DTCs). Refer to: Anti-Lock Brake System (ABS) and Stability Control .
- Position the vehicle onto an alignment rack with the front wheels in the straight ahead position.
- Turn the engine off.
- Remove the steering wheel. Refer to: Steering Wheel .
- Inspect the steering wheel end of the steering column shaft and the white SCCM ring.
- Confirm the steering column shaft hex flat is horizontal, the white SCCM ring tab is at the 12 o'clock position and the turn signal tab is centered on the disc activator as shown above.
- If the items are not positioned as shown, loosen the tie-rod jamb nuts and rotate the tie rods until the items are positioned as shown. Make sure to adjust both sides equally. Refer to: Front Toe Adjustment - F-250 F-350 F-450 F-550, 4WD .
- Confirm the steering column shaft hex flat is horizontal, the white SCCM ring tab is at the 12 o'clock position and the turn signal tab is centered on the disc activator as shown in Step 7.
- Install the steering wheel. This requires manually releasing the service lock and rotating the clockspring into position on the SCCM yellow posts. Refer to: Steering Wheel
.
- Set the ignition ON, engine off.
-
NOTE: Make sure the front wheels are in the straight ahead position during the trim procedure.
Using a diagnostic scan tool, carry out the steering motor angle trim routine. Follow all on-screen instructions.
- Carry out the front toe adjustment procedure. Refer to: Front Toe Adjustment - F-250 F-350 F-450 F-550, 4WD .
- Start the engine.
- Confirm correct steering wheel clear vision, turn signal operation and equal steering wheel rotation from lock-to-lock.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.