SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2021EDGE SE, 4WDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 590 (CRUISE CONTROL - VEHICLES WITH: ADAPTIVE CRUISE CONTROL)DIAGNOSIS AND TESTINGCRUISE CONTROLPINPOINT TESTSPINPOINT TEST M: U3003:17
2021 Ford Edge SE, 4WD

Pinpoint Test M: U3003:17

2021 Ford Edge SE, 4WDSECTION Pinpoint Test M: U3003:17
WARNING: This page is about a different car, the 2021 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.
  1. Refer to CRUISE CONTROL for schematic and connector information.

    Normal Operation and Fault Conditions 

    REFER to: Cruise Control - Vehicles With: Adaptive Cruise Control With Lane Centering - System Operation and Component Description .

    REFER to: Cruise Control - Vehicles With: Active Drive Assist/Intelligent Adaptive Cruise Control - System Operation and Component Description .

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    CCM U3003:17 Battery Voltage: Circuit Voltage Above Threshold Sets as a continuous memory and on-demand DTC if the CCM detects high battery voltage above 16.5 volts for 100 ms.

    Possible Sources 

    • Generator
    • CCM
    • PCM

  2. NOTE: DTC U3003:17 may be stored in the module memory due to past battery charging or vehicle jump starting events.

  3. M1 CHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) U3003:17, P0563:00 OR P0626:00 SET IN OTHER MODULES

    • Ignition ON.

    • Connect the diagnostic tool.

    • Using a diagnostic scan tool, retrieve the Continuous Memory Diagnostic Trouble Codes (CMDTCs) from all modules.

    Is DTC U3003:17, P0563:00 or P0626:00 set in more than one module? 

    Yes  REFER to the appropriate DTC Chart.
    No  GO to  M2

  4. M2 CHECK THE BATTERY VOLTAGE

    • Turn off all the interior/exterior lights and accessories.

    • Start and run the engine at approximately 2, 000 rpm for three minutes while monitoring the battery voltage.

    Does the battery voltage rise to 15.5 volts or higher? 

    Yes  For 2.7L, REFER to: Charging System - 2.7L EcoBoost (238kW/324PS)/3.5L EcoBoost (BM) . For 3.3L, 5.0L, REFER to: Charging System - 3.3L Duratec-V6/5.0L 32V Ti-VCT . For 3.0L Diesel, REFER to: Charging System - 3.0L Power Stroke Diesel .
    No  GO to  M3

  5. M3 RECHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) U3003:17

    • Ignition OFF.

    • Ignition ON.

    • Using a diagnostic scan tool, clear the DTC Continuous Memory Diagnostic Trouble Codes (CMDTCs).

    • Using a diagnostic scan tool, perform the CCM self-test.

    Is DTC U3003:17 still present? 

    Yes  INSTALL a new CCM. REFER to: Cruise Control Module (CCM) .
    No  The system is operating normally at this time. The DTC may have been set previously during battery charging or while jump starting the vehicle.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.