Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Pinpoint Test P: U0252:87
- Refer to MODULE COMMUNICATIONS NETWORK
for schematic and connector information.
Normal Operation and Fault Conditions
REFER to: Module Controlled Functions - System Operation and Component Description .
DTC Fault Trigger Conditions
DTC Description Fault Trigger Condition BCM U0252:87 Lost Communication With Lighting Control Module- Rear "B": Missing Message Sets in the BCM if messages from the TRM through the GWM are missing. Possible Sources
- Communication network concern
- Battery voltage concern
- GWM concern
- TRM
- BCM
- P1 CHECK THE COMMUNICATION NETWORK
- Ignition ON.
- Connect the diagnostic tool.
- Using a diagnostic scan tool, perform a network test.
Does the TRM pass the network test?
Yes GO to P2 No REFER to: Module Controlled Functions - System Operation and Component Description . - P2 CHECK THE BCM (BODY CONTROL MODULE) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)
- Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).
- Wait 10 seconds.
- Using a diagnostic scan tool, check the BCM CMDTCs.
Is DTC B11D9:16, B11D9:17, U3006:16, U3006:17, U3007:16, U3007:17, U3013:16, U3013:17, U3014:16 or U3014:17 recorded?
Yes For DTC B11D9:16, U3006:16, U3007:16, U3013:16 or U3014:16, GO to Pinpoint Test Y For DTC B11D9:17, U3006:17, U3007:17, U3013:17 or U3014:17, GO to Pinpoint Test Z No GO to P3 - P3 RETRIEVE THE TRM (TRAILER MODULE) DTCS
- Using a diagnostic scan tool, perform the TRM self-test.
Are any TRM DTCs recorded?
Yes REFER to: Trailer Lamps . No GO to P4 - P4 RECHECK THE BCM (BODY CONTROL MODULE) CMDTCS
- Using a diagnostic scan tool, clear the DTCs.
- Wait 10 seconds.
- Using a diagnostic scan tool, check the BCM CMDTCs.
Is DTC U0137:87 still present?
Yes GO to P5 No The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition. - P5 CHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) U0137:87 SET IN OTHER MODULES
- Using a diagnostic scan tool, clear the DTCs.
- Ignition OFF.
- Wait 10 seconds.
- Ignition ON.
- Using a diagnostic scan tool, retrieve all CMDTCs.
Is DTC U0137:87 set in other modules?
Yes GO to P6 No GO to P7 - P6 CHECK FOR CORRECT TRM (TRAILER MODULE) OPERATION
- Ignition OFF.
- Disconnect and inspect the Disconnect and inspect the TRM connectors.
- Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary
- Reconnect the TRM connectors. Make sure they seat and latch correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new TRM. REFER to: Trailer Module (TRM) . No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues. - P7 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
- Ignition OFF.
- Disconnect and inspect the BCM connectors.
- Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary
- Reconnect the BCM connectors. Make sure they seat and latch correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new BCM. REFER to: Body Control Module (BCM) . No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.