Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Typical Diagnostic Reference Values
2021 Ford Edge SE, 4WDSECTION Typical Diagnostic Reference Values
WARNING: This page does not describe the selected car, but rather 32 other vehicles, including the 2019 Lincoln Navigator, 2019 Lincoln Nautilus, 2019 Lincoln MKZ, 2019 Lincoln MKT, and 2019 Lincoln MKC. However, it is still accessible from the selected car via links, so may be relevant.
| Inputs | Component/PID Only | Measured/PID Values | Units Measured/PID | |||
|---|---|---|---|---|---|---|
| KOEO | Hot Idle | 48 KM/H (30 MPH) | 89 KM/H (55 MPH) | |||
| APP | APP Sensor | 0 | 0 | 15.5 | 26.5 | % |
| APP1 | APP Sensor | 0.74 | 0.74 | 1.25 | 1.36 | VOLTS |
| APP2 | APP Sensor | 0.36 | 0.37 | 0.63 | 0.68 | VOLTS |
| B+ | PID | 12.4 | 13-14 | 13-14 | 13-14 | VOLTS |
| BARO | PID | 14.3/156.2 | 14.3/156.2 | 14.05/154.7 | 14.3/156.2 | PSI/Hz |
| BOO1 | BPP Switch | OFF | OFF | OFF | OFF | ON/OFF |
| BOO2 | BPP Switch | OFF | OFF | OFF | OFF | ON/OFF |
| CHT | CHT Sensor | 0.61/89 (192.2) | 0.6/90 (194) | 3.58/94 (201.2) | 3.56/96 (204.8) | VOLTS/DEG C (DEG F) |
| ETC_TRIM | PID | 0.39 (J) | 0.43 (J) | 0.36 (J) | 0.36 (J) | DEG |
| FPM | Fuel Pump Control Module | 60.25 | 60.35 | 60.25 | 60.31 | % |
| FTP | FTP Sensor | 2.6/0 | 2.6/0 | 2.3/-0.07 | 2.1/-0.11 | VOLTS/PSI |
| IAT | IAT Sensor | 2.9/22.7 (73) | 3.3/15 (59) | 3.7/7.2 (45) | 3.7/6.1 (43) | VOLTS/DEG C (DEG F) |
| KNOCK_1 | KS1 Sensor | 0 | 0 | 301 | 525 | N/A |
| KNOCK_2 | KS2 Sensor | 0 | 0 | 289 | 448 | N/A |
| LOAD | PID | 0 (I) | 20 | 41 | 56 | % |
| LONGFT1 | PID | (I) | -20 TO +20 | -20 TO +20 | -20 TO +20 | % |
| LONGFT2 | PID | (I) | -20 TO +20 | -20 TO +20 | -20 TO +20 | % |
| MAF | MAF Sensor | 0/697 | 8/2.52 | 30/4.27 | 58/5.46 | g/s/Hz |
| MISFIRE | PID | NO | NO | NO | NO | YES/NO |
| O2S11_CUR | HO2S11 Sensor | (I) | switching | switching | switching | mA/uA |
| O2S12 | HO2S12 Sensor | (I) | (D) | (D) | (D) | VOLTS |
| O2S21_CUR | HO2S21 Sensor | (I) | switching | switching | switching | mA/uA |
| PTO | PID | OFF | OFF | OFF | OFF | ON/OFF |
| PTOIR_V | PID | 0.02 | 0.02 | 0.02 | 0 | VOLTS |
| PTOLOAD | PID | OFF | OFF | OFF | OFF | ON/OFF |
| RPM | CKP Sensor | 0 | 654 | 1127 | 1618 | RPM |
| SHRTFT1 | PID | (I) | -10 TO +10 | -10 TO +10 | -10 TO +10 | % |
| SHRTFT2 | PID | (I) | -10 TO +10 | -10 TO +10 | -10 TO +10 | % |
| VSS | PID | 0 | 0 | 48 km/h (30 MPH) | 89 km/h (55 MPH) | km/h/MPH |
| Outputs | Component/PID Only | Measured/PID Values | Units Measured/PID | |||
|---|---|---|---|---|---|---|
| KOEO | Hot Idle | 48 KM/H (30 MPH) | 89 KM/H (55 MPH) | |||
| EVAPCP | EVAPCP Valve | 0 | 0 | 0 | 99.9 | % |
| EVAPCV | CANV Valve | 0 | 0 | 0 | 0 | % |
| FP | Fuel Pump Control Module | 75 | 31 | 31 | 31 | % |
| IMTV | IMTV Solenoid | 0 | 0 | 0 | 0 | % |
| MIL | PID | OFF | OFF | OFF | OFF | ON/OFF |
| O2S11_HTR | HO2S11 Sensor | 22 | 36 | 30 | 21 | % |
| O2S21_HTR | HO2S21 Sensor | 22 | 36 | 29 | 21 | % |
| PTOIL | PTO Lamp | OFF | OFF | OFF | OFF | ON/OFF |
| SPARKADV | PID | 13.50 | 12.25 | 27.75 | 32 | DEG |
| Other | Component/PID Only | Measured/PID Values | Units Measured/PID | |||
|---|---|---|---|---|---|---|
| KOEO | Hot Idle | 48 KM/H (30 MPH) | 89 KM/H (55 MPH) | |||
| VPWR | PID | VBAT | VBAT | VBAT | VBAT | VOLTS |
| VREF | PID | 5 | 5 | 5 | 5 | VOLTS |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.