DTC Chart: DSM

2021 Ford Edge SE, 4WDSECTION DTC Chart: DSM
WARNING: This page is about a different car, the 2020 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.

Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .

DTC Description Action
B1298:24 Steering Column Adjust Up Switch: Signal Stuck High REFER to: Steering Column .
B1299:24 Steering Column Adjust Down Switch: Signal Stuck High REFER to: Steering Column .
B12A1:24 Steering Column Adjust Out Switch: Signal Stuck High REFER to: Steering Column .
B12A2:24 Steering Column Adjust In Switch: Signal Stuck High REFER to: Steering Column .
B12A7:11 Steering Column Tilt Sensor A: Circuit Short To Ground REFER to: Steering Column .
B12A7:12 Steering Column Tilt Sensor A: Circuit Short To Battery REFER to: Steering Column .
B12A8:11 Steering Column Telescope Sensor A: Circuit Short To Ground REFER to: Steering Column .
B12A8:12 Steering Column Telescope Sensor A: Circuit Short To Battery REFER to: Steering Column .
B1368:11 Adjustable Pedal Position Feedback Sensor: Circuit Short To Ground REFER to: Hydraulic Brake Actuation .
B1368:12 Adjustable Pedal Position Feedback Sensor: Circuit Short To Battery REFER to: Hydraulic Brake Actuation .
B1375:09 Steering Column Tilt Motor: Component Failure REFER to: Steering Column .
B1375:11 Steering Column Tilt Motor: Circuit Short To Ground REFER to: Steering Column .
B1375:12 Steering Column Tilt Motor: Circuit Short To Battery REFER to: Steering Column .
B1375:13 Steering Column Tilt Motor: Circuit Open REFER to: Steering Column .
B1375:1A Steering Column Tilt Motor: Circuit Resistance Below Threshold REFER to: Steering Column .
B1375:31 Steering Column Tilt Motor: No Signal REFER to: Steering Column .
B137D:09 Pedal Adjustment Motor: Component Failure REFER to: Hydraulic Brake Actuation .
B137D:11 Pedal Adjustment Motor: Circuit Short To Ground REFER to: Hydraulic Brake Actuation .
B137D:12 Pedal Adjustment Motor: Circuit Short To Battery REFER to: Hydraulic Brake Actuation .
B137D:13 Pedal Adjustment Motor: Circuit Open REFER to: Hydraulic Brake Actuation .
B137D:1A Pedal Adjustment Motor: Circuit Resistance Below Threshold REFER to: Hydraulic Brake Actuation .
B137D:31 Pedal Adjustment Motor: No Signal REFER to: Hydraulic Brake Actuation .
B137E:09 Steering Column Telescope Motor: Component Failure REFER to: Steering Column .
B137E:11 Steering Column Telescope Motor: Circuit Short To Ground REFER to: Steering Column .
B137E:12 Steering Column Telescope Motor: Circuit Short To Battery REFER to: Steering Column .
B137E:13 Steering Column Telescope Motor: Circuit Open REFER to: Steering Column .
B137E:1A Steering Column Telescope Motor: Circuit Resistance Below Threshold REFER to: Steering Column .
B137E:31 Steering Column Telescope Motor: No Signal REFER to: Steering Column .
B14C3:24 Seat Height Rear Down Switch: Signal Stuck High GO to Pinpoint Test H 
B14C4:24 Seat Height Rear Up Switch: Signal Stuck High GO to Pinpoint Test H 
B14C7:24 Adjustable Pedal Forward Switch: Signal Stuck High REFER to: Hydraulic Brake Actuation .
B14C8:24 Adjustable Pedal Rearward Switch: Signal Stuck High REFER to: Hydraulic Brake Actuation .
B14CB:11 Seat Height Rear Position Feedback: Circuit Short To Ground GO to Pinpoint Test I 
B14CB:12 Seat Height Rear Position Feedback: Circuit Short To Battery GO to Pinpoint Test I 
B14CE:09 Seat Horizontal Motor Output: Component Failure GO to Pinpoint Test H 
B14CE:11 Seat Horizontal Motor Output: Circuit Short To Ground GO to Pinpoint Test H 
B14CE:12 Seat Horizontal Motor Output: Circuit Short To Battery GO to Pinpoint Test H 
B14CE:14 Seat Horizontal Motor Output: Circuit Short To Ground or Open GO to Pinpoint Test H 
B14CE:15 Seat Horizontal Motor Output: Circuit Short To Battery or Open GO to Pinpoint Test H 
B14CE:1A Seat Horizontal Motor Output: Circuit Resistance Below Threshold GO to Pinpoint Test H 
B14CE:31 Seat Horizontal Motor Output: No Signal GO to Pinpoint Test I 
B14CF:09 Seat Recline Motor Output: Component Failure GO to Pinpoint Test H 
B14CF:11 Seat Recline Motor Output: Circuit Short To Ground GO to Pinpoint Test H 
B14CF:12 Seat Recline Motor Output: Circuit Short To Battery GO to Pinpoint Test H 
B14CF:14 Seat Recline Motor Output: Circuit Short To Ground or Open GO to Pinpoint Test H 
B14CF:15 Seat Recline Motor Output: Circuit Short To Battery or Open GO to Pinpoint Test H 
B14CF:1A Seat Recline Motor Output: Circuit Resistance Below Threshold GO to Pinpoint Test H 
B14CF:31 Seat Recline Motor Output: No Signal GO to Pinpoint Test I 
B14D0:09 Seat Height Front/Tilt Motor Output: Component Failure GO to Pinpoint Test H 
B14D0:11 Seat Height Front/Tilt Motor Output: Circuit Short To Ground GO to Pinpoint Test H 
B14D0:12 Seat Height Front/Tilt Motor Output: Circuit Short To Battery GO to Pinpoint Test H 
B14D0:14 Seat Height Front/Tilt Motor Output: Circuit Short To Ground or Open GO to Pinpoint Test H 
B14D0:15 Seat Height Front/Tilt Motor Output: Circuit Short To Battery or Open GO to Pinpoint Test H 
B14D0:1A Seat Height Front/Tilt Motor Output: Circuit Resistance Below Threshold GO to Pinpoint Test H 
B14D0:31 Seat Height Front/Tilt Motor Output: No Signal GO to Pinpoint Test I 
B14D2:09 Seat Height Rear Motor Output: Component Failure GO to Pinpoint Test H 
B14D2:11 Seat Height Rear Motor Output: Circuit Short To Ground GO to Pinpoint Test H 
B14D2:12 Seat Height Rear Motor Output: Circuit Short To Battery GO to Pinpoint Test H 
B14D2:14 Seat Height Rear Motor Output: Circuit Short To Ground or Open GO to Pinpoint Test H 
B14D2:15 Seat Height Rear Motor Output: Circuit Short To Battery or Open GO to Pinpoint Test H 
B14D2:1A Seat Height Rear Motor Output: Circuit Resistance Below Threshold GO to Pinpoint Test H 
B14D2:31 Seat Height Rear Motor Output: No Signal GO to Pinpoint Test I 
B1B89:11 Seat Slide Motor Speed/Position Sensor: Circuit Short To Ground GO to Pinpoint Test I 
B1B89:12 Seat Slide Motor Speed/Position Sensor: Circuit Short To Battery GO to Pinpoint Test I 
B1B91:11 Seat Tilt Motor Speed/Position Sensor: Circuit Short To Ground GO to Pinpoint Test I 
B1B91:12 Seat Tilt Motor Speed/Position Sensor: Circuit Short To Battery GO to Pinpoint Test I 
B1B93:11 Seat Recline Motor Speed/Position Sensor: Circuit Short To Ground GO to Pinpoint Test I 
B1B93:12 Seat Recline Motor Speed/Position Sensor: Circuit Short To Battery GO to Pinpoint Test I 
B1B96:24 Seat Slide Forward Switch: Signal Stuck High GO to Pinpoint Test H 
B1B97:24 Seat Slide Backward Switch: Signal Stuck High GO to Pinpoint Test H 
B1B98:24 Seat Tilt Up Switch: Signal Stuck High GO to Pinpoint Test H 
B1B99:24 Seat Tilt Down Switch: Signal Stuck High GO to Pinpoint Test H 
B1C00:24 Seat Recline Up Switch: Signal Stuck High GO to Pinpoint Test H 
B1C01:24 Seat Recline Down Switch: Signal Stuck High GO to Pinpoint Test H 
U0100:00 Lost Communication with ECM/PCM "A": No Sub Type Information GO to Pinpoint Test T 
U0140:00 Lost Communication with Body Control Module: No Sub Type Information GO to Pinpoint Test V 
U1000:00 Solid State Driver Protection Active -Driver Disabled: No Sub Type Information DIAGNOSE any other related DSM Diagnostic Trouble Codes (DTCs) first. CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U1000:00 returns, INSTALL a new DSM. REFER to: Driver Front Seat Module (DSM) .
U2100:00 Initial Configuration Not Complete: No Sub Type Information
NOTE: This DTC indicates PMI has not been carried out on a newly installed module or configuration data has been lost. Presence of this DTC alone does not prevent basic seat operation from the seat control switch.
Using a diagnostic scan tool, CARRY OUT PMI on the DSM. REPEAT the self-test and VERIFY successful PMI. CLEAR the Diagnostic Trouble Codes (DTCs).
U3000:49 Control Module: Internal Electronic Failure INSTALL a new DSM. REFER to: Driver Front Seat Module (DSM) .
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • You smell fuel, burning insulation, or see smoke.
  • Brakes feel soft, pull hard to one side, or make grinding noises.
  • The engine overheats, stalls repeatedly, or misfires under load.
  • You are missing required tools, torque specs, or safe lifting equipment.
  • You are not confident in the next step or safety outcome.