Safety Warning

DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.

SYS.OK|MANUAL.DB● LIVE

HOMESERVICE MANUALSFORD2021EDGE SE, 4WDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 221 (TRANSFER CASE)DISASSEMBLY AND ASSEMBLYTRANSFER CASE - VEHICLES WITH: ELECTRONIC SHIFT TRANSFER CASEASSEMBLY

2021 Ford Edge SE, 4WD

Transfer Case - Vehicles With: Electronic Shift Transfer Case: Assembly

2021 Ford Edge SE, 4WDSECTION Assembly

WARNING: This page is about a different car, the 2019 Ford F-550 Super Duty, 2019 Ford F-450 Super Duty, 2019 Ford F-350 Super Duty, and 2019 Ford F-250 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.

All vehicles except vehicles equipped with a 6R100 transmission built on or after 31-03-2017

Using the special tools, install the center support bearing. Use Special Service Tool: 205-153 (T80T-4000-W) Handle., 307-344 (T95P-7H150-A) Installer, Driven Sprocket Wheel.

Courtesy of FORD MOTOR COMPANY

All vehicles
Using the special tools, install the front planet carrier bearing. Use Special Service Tool: 205-153 (T80T-4000-W) Handle., 308-410 Installer, Output Shaft Front Bearing.

Courtesy of FORD MOTOR COMPANY
Using the special tools, install the front output shaft bearing. Use Special Service Tool: 205-153 (T80T-4000-W) Handle., 307-626 Installer, Differential Seal.

Courtesy of FORD MOTOR COMPANY
Using the special tools, install the front output shaft support bearing. Use Special Service Tool: 205-153 (T80T-4000-W) Handle., 307-626 Installer, Differential Seal.

Courtesy of FORD MOTOR COMPANY
Using the special tools, install the rear output shaft bearing. Use Special Service Tool: 205-153 (T80T-4000-W) Handle., 308-410 Installer, Output Shaft Front Bearing.

Courtesy of FORD MOTOR COMPANY
Using the special tools, install the shift shaft seal. Install Special Service Tool: 307-549 Installer, Shift Shaft Fluid Seal.

Courtesy of FORD MOTOR COMPANY
Using the special tools, install the input shaft seal. Use Special Service Tool: 205-1018 Installation Tube., 308-943 Installer, Input Seal.

Courtesy of FORD MOTOR COMPANY
Using the special tools, install the front output shaft seal. Use Special Service Tool: 205-153 (T80T-4000-W) Handle., 308-944 Installer, Front Output Seal.

Courtesy of FORD MOTOR COMPANY
NOTE: Do not let the front output shaft fall while removing the snap ring or damage to the component may occur.

Install the output shaft and the out put shaft circlip.

Courtesy of FORD MOTOR COMPANY
Install the ring gear and the ring gear circlip.

Courtesy of FORD MOTOR COMPANY
Install the planet carrier and the front planet carrier thrust bearing.

Courtesy of FORD MOTOR COMPANY
Install the electric shift cam assembly.

Courtesy of FORD MOTOR COMPANY
Install the reduction hub.

Courtesy of FORD MOTOR COMPANY
Install the output shaft.

Courtesy of FORD MOTOR COMPANY
Install the shift fork.

Courtesy of FORD MOTOR COMPANY
Install the shift rail.

Courtesy of FORD MOTOR COMPANY
Install the magnet and oil pump assembly.

Courtesy of FORD MOTOR COMPANY

All vehicles except vehicles equipped with a 6R100 transmission built on or after 31-03-2017
Install the center bearing support assembly.

Courtesy of FORD MOTOR COMPANY

Vehicles equipped with a 6R100 transmission built on or after 31-03-2017
Install the center support assembly.

Courtesy of FORD MOTOR COMPANY

All vehicles
NOTE: Install the drive chain and sprockets as an assembly.

Install the drive chain and sprockets.

Courtesy of FORD MOTOR COMPANY
Assemble the lockup hub assembly.

Courtesy of FORD MOTOR COMPANY
Install the lock up hub assembly, shift fork and shift fork spring.

Courtesy of FORD MOTOR COMPANY
Install the field coil housing.

Courtesy of FORD MOTOR COMPANY
Install the field coil housing snap ring.

Courtesy of FORD MOTOR COMPANY
Install the transfer case field coil.

Courtesy of FORD MOTOR COMPANY
NOTE: Only apply enough silicone sealant to seal the transfer case halves together and does not squeeze into the transfer case.

Apply a small bead of silicone sealant to the mating surface of the case half.

Material: Motorcraft® Ultra Silicone Sealant / TA-29

Courtesy of FORD MOTOR COMPANY
NOTE: Position the field coil bolts to align with the field coil bolt holes in the rear case. Position field coil wire through the field coil wire through hole in the case.

Position the transfer case halves and tighten the bolts in the sequence shown.

Torque: 23 lb.ft (31 Nm)

Fig 1: Transfer Case Component Location W/ Bolt Tightening Sequence
Courtesy of FORD MOTOR COMPANY
Install the transfer case field coil nuts.
Torque: 89 lb.in (10 Nm)

Courtesy of FORD MOTOR COMPANY
Install the transfer case rear seal. Refer to: Transfer Case Rear Seal - Vehicles With: Flanged Yoke .
Apply a small bead of silicone sealant to the transfer case shift motor mating surface.
Material: Motorcraft® Ultra Silicone Sealant / TA-29

Courtesy of FORD MOTOR COMPANY
NOTE: When installing the shift motor, tighten the bracket nuts last. Failure to follow the steps in the correct order may result in damage to the component.
1. Install the transfer case shift motor.
2. Install the transfer case shift motor bolts.
  Torque: 89 lb.in (10 Nm)
3. Install the transfer case shift motor bracket bolt.
  Torque: 89 lb.in (10 Nm)
4. Tighten the transfer case shift motor bracket nuts.
  Torque: 27 lb.in (3 Nm)
Courtesy of FORD MOTOR COMPANY
NOTE: After the coil wire is inserted into the connector, gently pull the wire back to verify the pin is locked inside the connector.

Install the coil wire pin in the electrical connector.
1. Insert the coil wire pin in the electrical connector.
2. Install the inner connector retainer.
Courtesy of FORD MOTOR COMPANY
Remove the transfer case from the transmission adjustable mounting arms. Use the General Equipment: Adjustable Mounting Arm